Subject	This build has been nothing but disasters from day one...
Posted by	Jayru on May 18, 2012 at 3:36 PM
	This message has been viewed 159 times.
In Reply To	Did i just turn my SPL radiator into a $500 paperweight? posted by Jayru on May 18, 2012 at 02:37 PM
Message	From the body to the turbos to the motor (and now this), the entire build has been one trainwreck after another. I am seconds away from calling the whole project off... 90 Twin Turbo Track Build - jsworks.org for more info!
Follow Ups	Did i just turn my SPL radiator into a $500 paperweight? - Jayru 14:37:29 05/18/12 Is it leaking? (n/m) - JonnyZ(SoCal) 14:40:27 05/18/12 No fluid in it, it was never even installed yet. - Jayru 14:44:24 05/18/12 yep - aliaZ 14:44:17 05/18/12 blame it on fedex (n/m) - fuzzymonkey 14:47:13 05/18/12 fail (n/m) - moxie (SF) 15:26:07 05/18/12 Too big a paperweight for my desk. Your's must be huge. (n/m) - treese88 14:50:17 05/18/12 you can cut both end tanks off & TIG those tubes closed. (n/m) - induetime 14:53:16 05/18/12 just curious where did you purchase it ? - ZWolf 15:14:59 05/18/12 Was the last one and Sean's (SPL) personal one - Jayru 15:39:23 05/18/12 Another discontinued SPL product? That sucks... (n/m) - Inzane 21:02:15 05/18/12 This build has been nothing but disasters from day one... - Jayru 15:36:48 05/18/12 Happens to all of us - Pilot.P 03:54:55 05/19/12 Can be fixed by experience radiator shop - OverZealous (CT) 15:36:48 05/18/12 I think you can get $1.14 a LB (n/m) - njz 15:47:20 05/18/12 lol (n/m) - ForceFedTT (SoCal) 04:35:10 05/19/12 Call a radiator shop. They can this it I'm sure. (n/m) - Draker (Eugene, OR) 16:24:13 05/18/12 Fixable....I've seen worst getting fixed. Just take it to a - TheTwinZ (Peru) 19:06:14 05/18/12 Call Bryan McCulloch, he built the rad, I'm sure he can - zgene4 19:28:34 05/18/12 yep (n/m) - aliaZ 23:09:04 05/18/12 Thanks guys for all the advice! - Jayru 19:29:44 05/18/12 Let us know how much$$$$ to repair (n/m) - njz 10:31:04 05/19/12 I would be so pissed. That sucks bro. (n/m) - Antihero 19:50:13 05/18/12 Just put some JB weld on it, it will be fine lol (n/m) - Gennosuke 20:50:17 05/18/12 This actually is a proven solution to these problems (n/m) - OverZealous (CT) 21:59:18 05/19/12 Yup, repairing aircraft heat exchangers we used epoxy - BlackholeZ 20:10:46 05/20/12 That can be fixed by a good Tig welder. (n/m) - Timmay 02:20:35 05/19/12
Post a Followup	You cannot reply to this message because you are not logged in.