Subject	I couldn't get it perfectly parallel either.
Posted by	Evan_Wright (Ca) on April 23, 2012 at 10:45 AM
	This message has been viewed 112 times.
In Reply To	Nice work. posted by MixManMash on April 23, 2012 at 10:36 AM
Message	Fortunately it doesn't matter too much since we are using the centerline method. Any error due to missalignment will be the same on both sides of the cam lobe. It is more important when you are degree'ing a cam using the duration at .050" lift method.
Follow Ups	A guide to VG cam degreeing - Evan_Wright (Ca) 00:09:35 04/23/12 Put this in Tech so we can vote... - BoneZ (MD) 00:15:39 04/23/12 Nice.. thanks and VTF - KongZTT GT28RS MD 00:41:17 04/23/12 I did save the HTML and can post it to tech. I wanted to - Evan_Wright (Ca) 00:43:26 04/23/12 Couple timing questions. - FuerGrissa 01:30:28 04/23/12 The lifters shouldn't drain unless you had your engine - Evan_Wright (Ca) 01:46:35 04/23/12 Thanks - FuerGrissa 01:57:48 04/23/12 Great write up! I have a question - Madhatter10-6 07:59:45 04/23/12 You can certainly adjust them on a dyno and play around - Evan_Wright (Ca) 08:23:36 04/23/12 cool..thanks for the clarification! (n/m) - Madhatter10-6 09:28:20 04/23/12 I was going to degree my cams and Greg talked me out of it. - MixManMash 22:52:20 04/23/12 excellent work. Also nice to see someone that can use a - XTZ 02:03:31 04/23/12 Re: A guide to VG cam degreeing - TReedsZ 04:56:34 04/23/12 well done (n/m) - aliaZ 07:05:21 04/23/12 Re: A guide to VG cam degreeing - apsbainc 07:58:44 04/23/12 Looking good. (n/m) - Woody75 (Denver) 09:15:28 04/23/12 Great work, thanks for sharing (n/m) - RobZ32 09:44:04 04/23/12 Forgot but thanks to Woody75 (Denver) for your help! - Evan_Wright (Ca) 09:52:08 04/23/12 Nice work. - MixManMash 10:36:07 04/23/12 I couldn't get it perfectly parallel either. - Evan_Wright (Ca) 10:45:21 04/23/12 Ahh, that makes a lot of sense. Thanks for your quick - MixManMash 11:16:08 04/23/12 It took me a long time on the first two cams. Maybe around - Evan_Wright (Ca) 11:24:36 04/23/12 Great Write Up Evan! (n/m) - Zski 10:37:49 04/23/12 very nice !! (n/m) - ztunerz 10:53:26 04/23/12 Great write up...thanks! (n/m) - TheTwinZ (Peru) 13:04:47 04/23/12 Funny I just finished reading an RB tech article - Obeeone 14:18:49 04/23/12 Wow, that's awesome! Thanks! (n/m) - DVDBURN (MD) 16:49:48 04/23/12 The guide has been re-posted to tech if you want to VTF (n/m) - Evan_Wright (Ca) 18:57:23 04/23/12
Post a Followup	You cannot reply to this message because you are not logged in.