Subject	You can certainly adjust them on a dyno and play around
Posted by	Evan_Wright (Ca) on April 23, 2012 at 8:23 AM
	This message has been viewed 117 times.
In Reply To	Great write up! I have a question posted by Madhatter10-6 on April 23, 2012 at 07:59 AM
Message	with the powerband. I intend to have SZ do the same for me aswell. But I've always wanted to see how it runs when the timing is exactly as the the Nissan engineers intended it to be. I suspect it should run smoother....maybe be a bit more responsive. Also, when I do have it dyno tuned it would be nice to have a proper baseline to compare with.
Follow Ups	A guide to VG cam degreeing - Evan_Wright (Ca) 00:09:35 04/23/12 Put this in Tech so we can vote... - BoneZ (MD) 00:15:39 04/23/12 Nice.. thanks and VTF - KongZTT GT28RS MD 00:41:17 04/23/12 I did save the HTML and can post it to tech. I wanted to - Evan_Wright (Ca) 00:43:26 04/23/12 Couple timing questions. - FuerGrissa 01:30:28 04/23/12 The lifters shouldn't drain unless you had your engine - Evan_Wright (Ca) 01:46:35 04/23/12 Thanks - FuerGrissa 01:57:48 04/23/12 Great write up! I have a question - Madhatter10-6 07:59:45 04/23/12 You can certainly adjust them on a dyno and play around - Evan_Wright (Ca) 08:23:36 04/23/12 cool..thanks for the clarification! (n/m) - Madhatter10-6 09:28:20 04/23/12 I was going to degree my cams and Greg talked me out of it. - MixManMash 22:52:20 04/23/12 excellent work. Also nice to see someone that can use a - XTZ 02:03:31 04/23/12 Re: A guide to VG cam degreeing - TReedsZ 04:56:34 04/23/12 well done (n/m) - aliaZ 07:05:21 04/23/12 Re: A guide to VG cam degreeing - apsbainc 07:58:44 04/23/12 Looking good. (n/m) - Woody75 (Denver) 09:15:28 04/23/12 Great work, thanks for sharing (n/m) - RobZ32 09:44:04 04/23/12 Forgot but thanks to Woody75 (Denver) for your help! - Evan_Wright (Ca) 09:52:08 04/23/12 Nice work. - MixManMash 10:36:07 04/23/12 I couldn't get it perfectly parallel either. - Evan_Wright (Ca) 10:45:21 04/23/12 Ahh, that makes a lot of sense. Thanks for your quick - MixManMash 11:16:08 04/23/12 It took me a long time on the first two cams. Maybe around - Evan_Wright (Ca) 11:24:36 04/23/12 Great Write Up Evan! (n/m) - Zski 10:37:49 04/23/12 very nice !! (n/m) - ztunerz 10:53:26 04/23/12 Great write up...thanks! (n/m) - TheTwinZ (Peru) 13:04:47 04/23/12 Funny I just finished reading an RB tech article - Obeeone 14:18:49 04/23/12 Wow, that's awesome! Thanks! (n/m) - DVDBURN (MD) 16:49:48 04/23/12 The guide has been re-posted to tech if you want to VTF (n/m) - Evan_Wright (Ca) 18:57:23 04/23/12
Post a Followup	You cannot reply to this message because you are not logged in.