Subject	Great write up! I have a question
Posted by	Madhatter10-6 on April 23, 2012 at 7:59 AM
	This message has been viewed 114 times.
In Reply To	The lifters shouldn't drain unless you had your engine posted by Evan_Wright (Ca) on April 23, 2012 at 01:46 AM
Message	In your response to FuerGrissa you had said "This guide is for those that have adjustable sprockets and want to fine tune the cam timing" I was under the impression that with adjustable cam gears people typically dialed them in on the dyno...is that not the case? From what my tuner told me the best approach was for me to set mine at Zero degrees and to let him adjust them based on dyno feedback. Is your approach just to get it closer so that there is less dyno time or does it get them dialed in from the start and eliminate the need for the dyno? Thanks! Madhatter10-6
Follow Ups	A guide to VG cam degreeing - Evan_Wright (Ca) 00:09:35 04/23/12 Put this in Tech so we can vote... - BoneZ (MD) 00:15:39 04/23/12 Nice.. thanks and VTF - KongZTT GT28RS MD 00:41:17 04/23/12 I did save the HTML and can post it to tech. I wanted to - Evan_Wright (Ca) 00:43:26 04/23/12 Couple timing questions. - FuerGrissa 01:30:28 04/23/12 The lifters shouldn't drain unless you had your engine - Evan_Wright (Ca) 01:46:35 04/23/12 Thanks - FuerGrissa 01:57:48 04/23/12 Great write up! I have a question - Madhatter10-6 07:59:45 04/23/12 You can certainly adjust them on a dyno and play around - Evan_Wright (Ca) 08:23:36 04/23/12 cool..thanks for the clarification! (n/m) - Madhatter10-6 09:28:20 04/23/12 I was going to degree my cams and Greg talked me out of it. - MixManMash 22:52:20 04/23/12 excellent work. Also nice to see someone that can use a - XTZ 02:03:31 04/23/12 Re: A guide to VG cam degreeing - TReedsZ 04:56:34 04/23/12 well done (n/m) - aliaZ 07:05:21 04/23/12 Re: A guide to VG cam degreeing - apsbainc 07:58:44 04/23/12 Looking good. (n/m) - Woody75 (Denver) 09:15:28 04/23/12 Great work, thanks for sharing (n/m) - RobZ32 09:44:04 04/23/12 Forgot but thanks to Woody75 (Denver) for your help! - Evan_Wright (Ca) 09:52:08 04/23/12 Nice work. - MixManMash 10:36:07 04/23/12 I couldn't get it perfectly parallel either. - Evan_Wright (Ca) 10:45:21 04/23/12 Ahh, that makes a lot of sense. Thanks for your quick - MixManMash 11:16:08 04/23/12 It took me a long time on the first two cams. Maybe around - Evan_Wright (Ca) 11:24:36 04/23/12 Great Write Up Evan! (n/m) - Zski 10:37:49 04/23/12 very nice !! (n/m) - ztunerz 10:53:26 04/23/12 Great write up...thanks! (n/m) - TheTwinZ (Peru) 13:04:47 04/23/12 Funny I just finished reading an RB tech article - Obeeone 14:18:49 04/23/12 Wow, that's awesome! Thanks! (n/m) - DVDBURN (MD) 16:49:48 04/23/12 The guide has been re-posted to tech if you want to VTF (n/m) - Evan_Wright (Ca) 18:57:23 04/23/12
Post a Followup	You cannot reply to this message because you are not logged in.