Subject	You didn't hear what I said
Posted by	CoHPhasor on February 21, 2012 at 10:02 PM
	This message has been viewed 176 times.
In Reply To	I have the 1st unit and mine is fine. posted by toykoz32 on February 21, 2012 at 09:37 PM
Message	The fact that you have a prototype makes your case less relevant. Prototypes by their nature are prone to more scrutiny. I have trouble believing that every rail going out the door is fully pressure tested. So, first, defective materials: The Nickel plating guy was a fucking idiot and plated the AN fittings. In case you didn't know, AN mating surfaces are extremely finicky, so they should NEVER be plated. Apparently while they were hanging to dry, it formed an uneven surface due to gravity. This made my rail leak profusely and I'm glad I scrutinized it, otherwise there'd be another "Well, my Z is toast" thread. As for the fuel temp sensor placement, NO it is NOT like factory. The fuel temp sensor screws *into a seat* on the factory rail which wholly envelops the sensor threads. The WINFactory unit, as I explained, threads through a ring and the bottom of the sensor then presses against the pipe. (~ a 1/16-1/8" gap between the ring and the rail) Those 2 scenarios are incredibly different. I'm don't know that you're aware, but sensors like that don't have a finite hotspot area of measurement on the bottom of them, the entire threaded area contributes to its measurement and the fact that some of that area is exposed to air movement makes it less accurate. Why is this explain logic day? This is truly ridiculous that I have to explain fact in this manner. Would anyone like reinforcement as to why they fall towards the Earth and not away from it while I'm at it?
Follow Ups	folks with top feed rails>>> - MikeVar82 12:31:37 02/21/12 Re: folks with top feed rails>>> - megaDan 15:38:13 02/21/12 A tab? so its used as a ground? On stock rail it goes to a - MikeVar82 15:44:08 02/21/12 fuel temp sensor? (n/m) - BoneZ (MD) 16:23:25 02/21/12 "a tab" is an improper description, I have the WINFactory .. - CoHPhasor 17:21:39 02/21/12 You always have bad to say about your rail. Makes one wonder - Z32TT-R 20:32:18 02/21/12 More of a commentary on design, and besides - CoHPhasor 20:57:55 02/21/12 I have the 1st unit and mine is fine. - toykoz32 21:37:25 02/21/12 You didn't hear what I said - CoHPhasor 22:02:28 02/21/12 While I'm at it, I might as well mention that the FTS mount - CoHPhasor 22:09:15 02/21/12 Your funny - toykoz32 22:32:32 02/21/12 Hey dopey, did I say it was in the way of the lines? - CoHPhasor 22:48:56 02/21/12 why not shave it alil then? some shaving is required to fit. - Z32TT-R 23:34:12 02/21/12 Calm down - toykoz32 00:43:32 02/22/12 I had made modifications to adapt it, this one - CoHPhasor 01:00:15 02/22/12 cut mine at a 45* angle, bolt still does its job, - Z32TT-R 01:31:11 02/22/12 Meh. The piece is just tack-welded in place.. - CoHPhasor 01:36:51 02/22/12 fo sho. (n/m) - Z32TT-R 02:08:20 02/22/12 The other kit has modifications too (n/m) - toykoz32 00:44:24 02/22/12 Re: "a tab" is an improper description, I have the WINFactory .. - megaDan 09:41:26 02/22/12 Second (+_=) (n/m) - Ba11erz (MD) 20:08:26 02/21/12 Since the fuel temp sensor is a part of the PRVR system - LitlElvis 09:56:17 02/22/12
Post a Followup	You cannot reply to this message because you are not logged in.