Subject	More of a commentary on design, and besides
Posted by	CoHPhasor on February 21, 2012 at 8:57 PM
	This message has been viewed 216 times.
In Reply To	You always have bad to say about your rail. Makes one wonder posted by Z32TT-R on February 21, 2012 at 08:32 PM
Message	my Cash Cannon only blows for a part once, unless it breaks. I *would* have gotten the BDE setup, hands down, no blinking - but. At the time Brett didn't allow you to keep cruise control, and when I asked him if he could he basically said there isn't a need for cruise when running top-feeds because they were for racing pretty much. Beyond that, I don't see a way to have the fuel temp sensor, which would still dissuade me. As for my commentary on the rail, Every point I've made has been valid. defective material early on, bad Q&A practice (early on), and the janky temp sensor bung that's welded on like a tab is not as desirable as a bung being welded directly to the pipe and act like a socket. That being said, the rail functions as described, my setup works, and I'm cool with it. Try not to wonder about me too much mom, I'll be fine. ;-)
Follow Ups	folks with top feed rails>>> - MikeVar82 12:31:37 02/21/12 Re: folks with top feed rails>>> - megaDan 15:38:13 02/21/12 A tab? so its used as a ground? On stock rail it goes to a - MikeVar82 15:44:08 02/21/12 fuel temp sensor? (n/m) - BoneZ (MD) 16:23:25 02/21/12 "a tab" is an improper description, I have the WINFactory .. - CoHPhasor 17:21:39 02/21/12 You always have bad to say about your rail. Makes one wonder - Z32TT-R 20:32:18 02/21/12 More of a commentary on design, and besides - CoHPhasor 20:57:55 02/21/12 I have the 1st unit and mine is fine. - toykoz32 21:37:25 02/21/12 You didn't hear what I said - CoHPhasor 22:02:28 02/21/12 While I'm at it, I might as well mention that the FTS mount - CoHPhasor 22:09:15 02/21/12 Your funny - toykoz32 22:32:32 02/21/12 Hey dopey, did I say it was in the way of the lines? - CoHPhasor 22:48:56 02/21/12 why not shave it alil then? some shaving is required to fit. - Z32TT-R 23:34:12 02/21/12 Calm down - toykoz32 00:43:32 02/22/12 I had made modifications to adapt it, this one - CoHPhasor 01:00:15 02/22/12 cut mine at a 45* angle, bolt still does its job, - Z32TT-R 01:31:11 02/22/12 Meh. The piece is just tack-welded in place.. - CoHPhasor 01:36:51 02/22/12 fo sho. (n/m) - Z32TT-R 02:08:20 02/22/12 The other kit has modifications too (n/m) - toykoz32 00:44:24 02/22/12 Re: "a tab" is an improper description, I have the WINFactory .. - megaDan 09:41:26 02/22/12 Second (+_=) (n/m) - Ba11erz (MD) 20:08:26 02/21/12 Since the fuel temp sensor is a part of the PRVR system - LitlElvis 09:56:17 02/22/12
Post a Followup	You cannot reply to this message because you are not logged in.