Subject	On the fuel topic. Would there be much of a restriction
Posted by	PiotrC70 on February 06, 2012 at 9:26 AM
	This message has been viewed 153 times.
In Reply To	Im in the market for an aeromotive fpr and pump .... posted by Xteam300TT (South Tx ) on February 05, 2012 at 09:29 PM
Message	using 2 90*'s on the fuel filter. 1 at the bottom (maybe 2" from the nipple) and the same on the outlet? I could maybe get away with 45*'s? Looking at relocating the fuel filter. 1993 TT. R.I.P. 09.15.2010
Follow Ups	Im in the market for an aeromotive fpr and pump .... - Xteam300TT (South Tx ) 21:29:23 02/05/12 Im also looking at aeromotive FPR and AN fittings - timmaz 22:14:37 02/05/12 I think the stock feed is ~8mm or ~5/16in - FuerGrissa 22:37:56 02/05/12 I used a -5 x -6AN Male Adapter and 5AN Tube Nut/Sleeve - Zinn2win 10:42:43 02/06/12 I used -6 AN for everything. I used the aeromotive - ShakaShaun(Denver) 22:56:32 02/05/12 Your bay is stunning, more pics? (n/m) - FuerGrissa 01:23:13 02/06/12 Thanks, a lot of work went into it. here are a few. - ShakaShaun(Denver) 20:10:48 02/06/12 Any reason you didnt use a 45 out of the filter instead?? (n/m) - Woody75 (Denver) 14:08:32 02/07/12 The angle ended up being better. (n/m) - ShakaShaun(Denver) 18:06:34 02/07/12 Where'd you get the bracket to hold the filter down? - CoHPhasor 02:29:13 02/06/12 It's an aeromotive bracket. It's way too expensive - ShakaShaun(Denver) 20:12:29 02/06/12 You can modify the stock bracket as well. - Woody75 (Denver) 14:18:38 02/07/12 Very interesting, thanks for the look! - CoHPhasor 18:29:01 02/07/12 I really like your setup. Especially the routing - Boosted1 06:10:24 02/06/12 There isn't really a limit to flow on a given diameter line - FuerGrissa 22:30:34 02/05/12 The limit isn't just HP, but fluid being moved - CoHPhasor 02:31:10 02/06/12 I'm having custom hardlines mandrel bent in 1/2in stainless - FuerGrissa 04:12:07 02/06/12 Nice. - CoHPhasor 04:58:10 02/06/12 BTW I have a new Aeromotive FPR I'd part with - FuerGrissa 22:55:58 02/05/12 You could always run a junction back into the FPR (n/m) - KongZTT GT28RS MD 00:06:44 02/06/12 On the fuel topic. Would there be much of a restriction - PiotrC70 09:26:12 02/06/12 Nope, will work fine (n/m) - Woody75 (Denver) 14:47:08 02/07/12 Thanks Tim! (n/m) - PiotrC70 20:38:10 02/07/12 Re: Im in the market for an aeromotive fpr and pump .... - njz 12:15:42 02/06/12 A1000 only way to go>>>> - dusthis 13:47:14 02/07/12
Post a Followup	You cannot reply to this message because you are not logged in.