Subject	give people an inch, they ALWAYS take a mile
Posted by	LJZTT on January 28, 2012 at 5:29 AM
	This message has been viewed 164 times.
In Reply To	To those that work on Zs posted by BlackholeZ on January 27, 2012 at 09:05 PM
Message	You need to be very careful Dan. While I wouldnt hesitate to help someone out, it would be on the premise that THEY are doing the job and *I* will assist them. Sure you may end up turning a few wrenches while they watch, but make sure that is the premise going in. I dunno what you feel is your competency level is with these cars, but you are inviting a major major headache if you let people believe that you are the fix-my-Z guy and let them just dump their neglected problems on you and charge them for your time in $. Me personally, I wouldnt do any maintenance or "fixing".....the most I'd do for anyone is help them install mods or delete stuff and again, I'd make them do the work at my garage with my tools with me helping out to make sure the car leaves at the end of the day. "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." --Winston Churchill "The last official act of any government is to loot the treasury." --George Washington END THE FED ....learn why, in 42 minutes Full Pardon for PFC Bradley Manning
Follow Ups	To those that work on Zs - BlackholeZ 21:05:52 01/27/12 hmmm - Jiro 21:27:09 01/27/12 Decide what your time is worth, and something's difficulty - CoHPhasor 21:28:47 01/27/12 Re: Decide what your time is worth, and something's difficulty - smartone 21:47:36 01/27/12 that's the rub - BlackholeZ 23:15:34 01/27/12 These cars are 20 years old...assume they will break - ConVerTT 23:35:28 01/27/12 Thats really good advice. When my swap got done - new2boost 12:52:05 01/28/12 they are 20 years old, change them even if they dont break - pearlzed(toronto) 02:58:05 01/28/12 Buy several feet of the proper silicone hose per the writeup - CoHPhasor 12:44:43 01/28/12 That's an interesting idea - BlackholeZ 13:54:53 01/28/12 Ahh. I'd still try for Silicone replacements, but OEM - CoHPhasor 14:34:40 01/28/12 what do you use to cut the PCV hoses? (n/m) - WhiTTe Z 14:53:03 01/28/12 Anything. I used diagonal cutters. (dikes) (n/m) - CoHPhasor 16:57:53 01/28/12 \/ fyi you can delete posts that nobody has replied to \/ (n/m) - BlackholeZ 18:05:25 01/28/12 they are usually pretty good when things break - nissan300zxwork 12:21:00 01/28/12 Re: To those that work on Zs - ouikikazz 21:57:08 01/27/12 Besides figuring out what your time is worth and - PiotrC70 22:31:15 01/27/12 Re: To those that work on Zs - team7 23:44:59 01/27/12 Dremeling an injector for a friend = 6 pack - BlackholeZ 01:43:23 01/28/12 give people an inch, they ALWAYS take a mile - LJZTT 05:29:02 01/28/12 "No" is a valuable word. Developing the ability to say, - zellamay 07:41:37 01/28/12 Sigh. I need to learn to say "no" (n/m) - aliaZ 08:46:46 01/28/12 lol i'm sorry man i had no one else to go to! (n/m) - ChrisMedaris 11:22:02 01/28/12 ive been doing private Z work at home for several years now - Dane (Houston) 09:17:30 01/29/12 Thanks a lot Dane! - BlackholeZ 15:36:26 01/29/12 good info, thanks - aliaZ 16:16:32 01/29/12 Dane, do you have a flat rate to replace a heater core? (n/m) - Dustin 20:02:38 01/29/12 Re: ive been doing private Z work at home for several years now - Krazyd27(Houston) 10:20:01 01/30/12
Post a Followup	You cannot reply to this message because you are not logged in.