Subject	Want me to make a bunch of .600 spacers?
Posted by	BlackholeZ on January 27, 2012 at 1:35 PM
	This message has been viewed 484 times.
In Reply To	300 Degree Camber Kit modification needed for camber setting posted by Gordo 93TT Daytona on January 26, 2012 at 09:44 PM
Message	I'm not trying to steal 300Degree's business, but I could whip a pile of these out real quick. -Dan BlackholeZ VTC Solenoid Caps and Installation Procedure "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	300 Degree Camber Kit modification needed for camber setting - Gordo 93TT Daytona 21:44:50 01/26/12 You're fine the bolts are 10.9 grade or better and they - Bernie (NoVA) 01:19:29 01/27/12 Any ideas one where to find 1" x '5/16ths" alum bar stock? - Gordo 93TT Daytona 07:01:39 01/27/12 I'm thinking you will need to have it made - FuerGrissa 08:27:38 01/27/12 Lowes sells various thickness by me. (n/m) - Bernie (NoVA) 08:45:43 01/27/12 They had 1 x .125 only here. I'd prefer not to stack them. - Gordo 93TT Daytona 08:59:57 01/27/12 There's not a Grainger near you? Usually you can go in - BigTDogg (MA) 09:20:00 01/27/12 Home Depot had more bar stock than the Grainger here. - Gordo 93TT Daytona 09:25:04 01/27/12 Re: Any ideas one where to find 1" x '5/16ths" alum bar stock? - rodelb 10:07:21 01/27/12 Found some 1 x 1/4 and 1 x 1/8 at ACE - Good to Go. - Gordo 93TT Daytona 11:19:10 01/27/12 On my previous Z, I used washers. - PiotrC70 12:18:32 01/27/12 I machined up a set of different sizes... - Gordo 93TT Daytona 12:57:51 01/27/12 Want me to make a bunch of .600 spacers? - BlackholeZ 13:35:41 01/27/12 I asked Kyle to forward that suggestion to 300 Degree... - Gordo 93TT Daytona 13:47:21 01/27/12 I'd at least let them have first pass at it - BlackholeZ 19:35:20 01/27/12 IMO An adjustable FUCA with silicon filled rubber bushing - Gordo 93TT Daytona 20:17:59 01/28/12 I've seen shops slot the UCA bracket to give - KongZTT GT28RS MD 16:43:30 01/27/12 What am I missing here? - Jkova300z 18:11:48 01/27/12 This---> - BoneZ (MD) 20:16:02 01/27/12 Considering maybe Stillen? (urethane vs steel roller) (n/m) - CoHPhasor 17:35:33 01/28/12 what's up with that ams box? (n/m) - 90GoldZ 20:29:18 01/27/12 it's the UCAs. they are AMS, and he's removing them and - Halo TTZ 21:09:48 01/27/12 I want the car lowered, but avoid impact harshness and noise - Gordo 93TT Daytona 10:05:46 01/28/12 FWIW.. RSR springs do not have the "jarring" effect - KongZTT GT28RS MD 10:35:54 01/28/12 Also, the Eibach are progressive rate.. - KongZTT GT28RS MD 10:37:29 01/28/12 The Jarring effect came from the aftermarket T-rods and UCA. - Gordo 93TT Daytona 11:08:41 01/28/12 Yea I just sold the set of new TT RSR springs to - KongZTT GT28RS MD 11:19:08 01/28/12 I'm happy that you chased this down! - BoneZ (MD) 19:46:47 01/28/12 Check your email. (n/m) - Dallas DamonZ 13:41:34 01/28/12 Thanks again Damon. (n/m) - Gordo 93TT Daytona 20:19:29 01/28/12
Post a Followup	You cannot reply to this message because you are not logged in.