Subject	Re: Re: Re: I guess the question is whether or not you understood
Posted by	Twin-TurboZ on January 14, 2012 at 12:10 AM
	This message has been viewed 149 times.
In Reply To	Re: Re: I guess the question is whether or not you understood posted by 94ttz32 on January 13, 2012 at 11:14 AM
Message	That is interesting to note, the last coated engine i had on the dyno was a vg30dett with similar mods to yours except the jwt 700 turbos instead of the 2530's It did not like any more than about 16 deg @20psi with no water/meth (on pump gas) mind you i do use a dyna-pac so it might be loading the engine a bit more than an inertia dyno. with the water on it would run clean at 22-23 deg advance with 20 psi and just over 500 at the wheels. Did not go any higher on the boost as the plug gaps needed to be reduced and we ran out of time.. Will put it back on the dyno again in the spring and see how it responds to some more boost. Your high boost run was that on pump gas ? were you using water/meth? Zeya
Follow Ups	extrude hone is it worth it! - 94ttz32 17:57:35 01/12/12 Re: extrude hone is it worth it! - assAssasin 18:02:53 01/12/12 For More Air movement? - TReedsZ 18:12:41 01/12/12 Re: For More Air movement? - 94ttz32 18:56:48 01/12/12 has anyone tried cxracing cast manifolds - JoeyG90Z22 18:19:38 01/12/12 Crap. Just as bad as the other copies out there! - JonnyZ(SoCal) 18:26:26 01/12/12 Re: has anyone tried cxracing cast manifolds - 94ttz32 18:28:04 01/12/12 If you can buy it from ebay its probably a waste... - new2boost 19:09:46 01/12/12 Re: If you can buy it from ebay its probably a waste... - JoeyG90Z22 19:26:43 01/12/12 Not to be a jerk but you have ALOT to learn... - new2boost 21:28:31 01/12/12 Re: has anyone tried cxracing cast manifolds - 94ttz32 19:25:12 01/12/12 Re: Re: has anyone tried cxracing cast manifolds - JoeyG90Z22 19:32:35 01/12/12 Re: Re: Re: has anyone tried cxracing cast manifolds - 94ttz32 19:45:10 01/12/12 I'm gonna stop before this happens - JoeyG90Z22 20:10:15 01/12/12 Re: I'm gonna stop before this happens - Tech@EPR 02:07:33 01/13/12 Just wondering... - SimaYi 20:42:44 01/12/12 horrible grammar = quoted HP - 200, so 475hp. (n/m) - evan_aggie(ATX) 21:05:35 01/12/12 Re: Just wondering... - 94ttz32 21:43:19 01/12/12 Good deal. - SimaYi 22:47:42 01/12/12 I wouldn't pay to do a lower plenum since it's 100% - LitlElvis 20:44:58 01/12/12 my turbo housings are extrude honed .. depends if you - The Devils Z 21:48:56 01/12/12 Re: my turbo housings are extrude honed .. depends if you - 94ttz32 22:01:09 01/12/12 wow, thats good power for being full boost before 6k. - nissan300zxwork 22:32:54 01/12/12 I don't know much about tuning, but... - SimaYi 22:52:34 01/12/12 Re: I don't know much about tuning, but... - Tech@EPR 01:58:47 01/13/12 Re: Re: my turbo housings are extrude honed .. depends if you - soulpwr 23:50:35 01/12/12 they quoted me $300 per housing - aliaZ 09:52:15 01/13/12 Re: they quoted me $300 per housing - 94ttz32 12:00:37 01/13/12 I didn't do a before/after...sorry (n/m) - aliaZ 12:34:37 01/13/12 Man, that gives value to the saying "It isn't what's on the - Ash's Z 22:42:53 01/12/12 Re: Man, that gives value to the saying "It isn't what's on the - 94ttz32 23:03:10 01/12/12 The exhaust portwork looks really good. :) - Ash's Z 23:58:39 01/12/12 Re: The exhaust portwork looks really good. :) - 94ttz32 00:04:57 01/13/12 Will be interesting to see the results of that. Have you - Ash's Z 03:01:18 01/13/12 Re: The exhaust portwork looks really good. :) - Tech@EPR 01:30:28 01/13/12 your nuts - nissan300zxwork 23:05:53 01/12/12 Re: your nuts - 94ttz32 23:11:09 01/12/12 I guess the question is whether or not you understood - Ash's Z 01:26:55 01/13/12 Re: I guess the question is whether or not you understood - Twin-TurboZ 02:51:20 01/13/12 Re: Re: I guess the question is whether or not you understood - 94ttz32 11:14:19 01/13/12 Re: Re: Re: I guess the question is whether or not you understood - Twin-TurboZ 00:10:09 01/14/12 Re: Re: Re: Re: I guess the question is whether or not you understood - 94ttz32 07:24:19 01/14/12 Re: Re: Re: I guess the question is whether or not you understood - Twin-TurboZ 00:19:15 01/14/12 What about his nuts? :) (n/m) - BigTDogg (MA) 13:33:41 01/13/12 Makes sense :-) (n/m) - OverZealous (CT) 20:11:45 01/14/12 Evan has an extrude honed plenum. Wright (CA) (n/m) - CoHPhasor 17:45:08 01/14/12
Post a Followup	You cannot reply to this message because you are not logged in.