Subject	LOL, I had to make an extension tool for one of my
Posted by	Ash's Z on December 22, 2011 at 10:23 PM
	This message has been viewed 418 times.
In Reply To	"non accredited installer error" (n/m) posted by Bernie (NoVA) on December 22, 2011 at 10:19 PM
Message	lathe/mill dial indicators I use for machine work and a setup jig to place the rod down into the plug bore and onto the piston crown. Measured TDC to within a thousandth of an inch. AMS=0, minus 6 degrees. Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	Been a long 3 days of tuning, but we got efficiency results! - Ash's Z 20:37:59 12/22/11 Awesome! cant wait for the results. Ordering V3's soon! (n/m) - timmaz 20:42:32 12/22/11 SCREEN SHOT of final tune with data collected.. - Ash's Z 20:50:33 12/22/11 Good work - michaell32 21:16:54 12/22/11 Z's MOD LIST - Ash's Z 21:32:05 12/22/11 Can't wait to hear vuks response to this. (n/m) - Wright (Ca) 21:39:09 12/22/11 "non accredited installer error" (n/m) - Bernie (NoVA) 22:19:14 12/22/11 LOL, I had to make an extension tool for one of my - Ash's Z 22:23:13 12/22/11 I'm sure that's not the only AMS pulley w the issue as well. - Bernie (NoVA) 23:47:35 12/22/11 you should get exhaust cam gears as well ... good - The Devils Z 21:54:50 12/22/11 ... and an ignition amplifier - it was just beginning to - Ash's Z 22:06:34 12/22/11 I am considering the exhaust cam gears, what is the - ae300z 22:16:07 12/22/11 Re: SCREEN SHOT of final tune with data collected.. - 94ttz32 21:48:23 12/22/11 Well done across the board Ash..... (n/m) - samsungZ [Houston] 23:13:10 12/22/11 Awesome! Will the ARC side mounts that you converted... - Madhatter10-6 08:52:52 12/23/11 Consistent, repeatable, and realistic intercooler fan flow/ - not4resaleZ 10:28:23 12/23/11 While I have no doubt that your intercoolers are good, - LitlElvis 11:22:04 12/23/11 Good point. Perhaps you need to log temp data - not4resaleZ 11:53:36 12/23/11 Am i reading this right? 32 psi on hks 2530 ? (n/m) - ztunerz 12:41:15 12/24/11 Re: Am i reading this right? 32 psi on hks 2530 ? - 94ttz32 15:57:09 12/24/11 Congrats Ash...! With all of your hard work is paying off. - Zski 20:55:52 12/22/11 sounds like it was a very productive time, Good Job. (n/m) - Halo TTZ 21:53:11 12/22/11 Thanks Ric! (n/m) - Ash's Z 21:58:02 12/22/11 Well it's about time! I've been waiting! (n/m) - OverZealous (CT) 22:17:46 12/22/11 Good stuff Ash!! (n/m) - Rich@RDZ 07:17:37 12/23/11 Good to see it all come together... Especially w/the V3's. (n/m) - Gordo 93TT Daytona 07:55:13 12/23/11 Excellent results Ash...keep up the hard work! (n/m) - MikeD (Philly) 10:11:16 12/23/11 are you ignoring my questions about your radiator - aliaZ 10:17:08 12/23/11 Congratulations - RobZ32 10:18:12 12/23/11 Couple questions for you Ash - black300zx 19:59:37 12/23/11 I think he is still making his own, atleast 5 months ago he - toykoz32 21:25:07 12/23/11 V3's are outsourced. (n/m) - Evan(CA) 21:47:27 12/23/11 I know . . . - toykoz32 00:04:26 12/24/11 Casting end tanks /= making the cores - black300zx 10:55:16 12/24/11
Post a Followup	You cannot reply to this message because you are not logged in.