Subject	I run no brace and don't have any issues at track events
Posted by	vorpalZ on December 07, 2011 at 2:32 PM
	This message has been viewed 209 times.
In Reply To	Well I plan to track the car and everything I've read posted by Jayru on December 07, 2011 at 12:54 PM
Message	Although if I were to investigate a proper fstb for the 300ZX., it would be tension adjustable, something like this: Regards, WARNING!  Forum posts are likely to contain traces of irony. If you believe you may be suffering from an irony deficiency please consult your physician. My Zs are hybrid vehicles, they run on gasoline and money I'm off to wax mine and go for a drive now. - BigTDogg (MA) 07:17:08 07/17/09 times change, people change, but the Z32 still kicks ass. - apudapus 16:46:02 06/15/07 I was more wondering how you set your climate control to 22* lol, it would be that fastest freezer on wheels! - Briscoe'sZ32 (NJ) 23:15:44 02/05/07 You have *got* to be getting a cut from B&B :D - SeedyROM 15:24:29 08/16/06 What do you think B&B stands for? - YugoBernie (NoVA) 15:57:09 08/16/06
Follow Ups	Worth modifying this strut tower bar? - Jayru 23:00:38 12/06/11 Put that Chinese POS in the trash. - Bernie (NoVA) 23:07:42 12/06/11 Re: Put that Chinese POS in the trash. - njz 06:09:59 12/07/11 Bernie has a picture for every situation. - Barry(TN) 07:45:26 12/07/11 Obviously the person didn't modify the fuel lines - Jayru 08:51:14 12/07/11 If you got it for free, sell it to an idiot and make dollas (n/m) - BigTDogg (MA) 08:53:34 12/07/11 Thought of that last night - Jayru 08:58:49 12/07/11 That's why I made mine into a towel rack by the garage sink - J-Mart 11:14:48 12/07/11 Re: That's why I made mine into a towel rack by the garage sink - CmyZ 13:02:42 12/07/11 I wouldn't modifiy my fuel system to fit around junk that - Bernie (NoVA) 12:04:28 12/07/11 Settle down, I said I see your point... (n/m) - Jayru 12:23:05 12/07/11 You're welcome. (n/m) - Bernie (NoVA) 13:06:28 12/07/11 better question to ask yourself is do you need a front brace (n/m) - LJZTT 12:22:49 12/07/11 Well I plan to track the car and everything I've read - Jayru 12:54:11 12/07/11 I run no brace and don't have any issues at track events - vorpalZ 14:32:43 12/07/11 how do you think adding stiffness to the front end will - LJZTT 20:57:58 12/07/11 This is basic chassis dynamics - Jayru 21:37:23 12/07/11 congratulations you have won the spec sheet grand prix - LJZTT 03:29:53 12/08/11 I dremeled the bar to clear the hard fuel line... - cherryz 15:35:55 12/07/11 SPL Fender Braces (n/m) - BoneZ (MD) 23:45:24 12/06/11 Thought these were nla? (n/m) - new2boost 07:33:26 12/07/11 I believe they are. Been looking for a set - Jayru 08:53:13 12/07/11 Not sure if they're still available, but... - Ted (92TT) 10:33:01 12/07/11 2nd. Planning on going with these. (n/m) - PiotrC70 10:59:37 12/07/11 Thanks for the link! Think it has the quality of the old SPL - Jayru 11:20:11 12/07/11 Another site, same product. - PiotrC70 13:18:11 12/07/11 Those are SPL . . SPL got them from Nagisa (n/m) - toykoz32 23:56:11 12/07/11 Bought mine from this place. - sak01 22:06:00 12/07/11 Glad I found a used set a while back... - na300zx (OH) 19:34:19 12/07/11 Re: SPL Fender Braces - CmyZ 15:50:03 12/07/11 That bar flexes, not good. (n/m) - Spongerider :) 01:16:29 12/07/11 no (n/m) - ZiNnYc 06:41:47 12/07/11 Are Powertrix strut bars acceptable? - Jayru 08:56:18 12/07/11 The Carbing is worth it though and the result are too. - zICEman(East TN) 09:16:40 12/07/11 Worm clamps don't belong on fuel injection line. (n/m) - Bernie (NoVA) 12:05:52 12/07/11 It's an old picture. Fuel line, regulators and clamps - zICEman(East TN) 13:22:25 12/07/11 Sorry Bernie - I beg to differ. Been using an aircraft - jzack 18:28:44 12/07/11 Ok fine "regular" worm clamps don't belong on FI line. - Bernie (NoVA) 00:27:13 12/08/11 There ya go!!!! LOL (n/m) - jzack 18:34:39 12/08/11 I bought a PowerTrix rear strut bar that you're more than - Mike TDK (NoVA) 10:12:29 12/08/11 buying the PowerTrix is like buying from AMS - Adam (NoVA) 11:28:33 12/07/11 False. - rojoloco (San Diego) 14:03:58 12/07/11 I bought a used Carbing bar from Charles just before he - Evan(CA) 14:27:45 12/07/11 I'm sure there must have been some comparison in R&D. - rojoloco (San Diego) 09:47:26 12/08/11 so the one piece design, the shape of the bar, material used - Adam (NoVA) 17:46:18 12/07/11 There are really only 2 ways to make the bar. - rojoloco (San Diego) 09:44:30 12/08/11 Or... - Bernie (NoVA) 10:43:41 12/08/11 This only proves my point. - rojoloco (San Diego) 13:04:45 12/08/11 carbing = original. powertrix = copy. - Adam (NoVA) 14:58:15 12/08/11 Carbing = genius starting platform. Powertrix = R&D original - rojoloco (San Diego) 16:43:29 12/08/11
Post a Followup	You cannot reply to this message because you are not logged in.