Subject	Damn it
Posted by	Broke_as_**** on December 06, 2011 at 8:40 PM
	This message has been viewed 196 times.
In Reply To	With BDE low profile mounts it is really easy........ posted by Greg D. (Specialty-Z) on December 06, 2011 at 05:12 PM
Message	I almost made through 2011 without spending a wad of cash on mods for the Z. Didn't buy the black Enkeis, didn't get a Blitz, didn't even buy those Recaros or some BDE motor mounts even though I should have. I did pick up a Zspeed clutch fork kit but hey, it's the Z, anything under $100 doesn't count.
Follow Ups	Anybody try to install Ash's inlet planar piping with the - fuzzymonkey 15:58:18 12/06/11 You're kidding right? - samsungZ (Houston) 16:14:00 12/06/11 Settle down all ready. - Bernie (NoVA) 16:21:18 12/06/11 The Big B man, been awhile... - samsungZ (Houston) 16:24:40 12/06/11 Not much has changed with you either it seems... (n/m) - Aqualung 18:32:17 12/06/11 *an - new2boost 17:25:37 12/06/11 A few times.... - Ash's Z 16:17:10 12/06/11 What kind of gains can be expected on a stock/SP500 turbo? (n/m) - madscientist222 17:35:30 12/06/11 Nick's got mail ... (n/m) - ConVerTT 20:21:05 12/06/11 With BDE low profile mounts it is really easy........ - Greg D. (Specialty-Z) 17:12:34 12/06/11 Greg...question - new2boost 17:32:13 12/06/11 Well.......... - Greg D. (Specialty-Z) 18:11:21 12/06/11 I also ducted air from under the car to feed the radiator - Greg D. (Specialty-Z) 18:17:39 12/06/11 What about Deans car? Does he drive on the street much? - Boosted1 18:33:53 12/06/11 Dean drives his car every day, he does not have A/C - Greg D. (Specialty-Z) 19:49:34 12/06/11 are we talking about grinding a bit of the motor mounts? (n/m) - fuzzymonkey 18:33:45 12/06/11 Correct (n/m) - Greg D. (Specialty-Z) 19:50:41 12/06/11 Damn it - Broke_as_**** 20:40:08 12/06/11 Thanks for the clarification - I typed my response in on my - Ash's Z 09:25:56 12/07/11 Difficult in my opinion... - ZonaZ 19:14:52 12/06/11 The indents in the stock pipes are the reason why I want to - Greg D. (Specialty-Z) 20:03:40 12/06/11 Is it fair to say it might be faster for most to just pull - ConVerTT 20:18:08 12/06/11 That's what I ultimately decided to do. The problem with - Wright (Ca) 20:28:11 12/06/11 I think you were looking for an excuse to do more :-P (n/m) - Greg D. (Specialty-Z) 20:36:54 12/06/11 Not in my opinion, for me it is a reasonable job to do - Greg D. (Specialty-Z) 20:35:23 12/06/11 if you're installing BDE motor mounts as well, yes. (n/m) - vorpalZ 09:49:13 12/07/11 +1 on every point. (n/m) - Stadsport (PHX) 21:53:52 12/06/11
Post a Followup	You cannot reply to this message because you are not logged in.