Subject	A few times....
Posted by	Ash's Z on December 06, 2011 at 4:17 PM
	This message has been viewed 366 times.
In Reply To	Anybody try to install Ash's inlet planar piping with the posted by fuzzymonkey on December 06, 2011 at 03:58 PM
Message	Drivers side usually gives the most headache.. Getting the upper inner inlet pipe flange bolt is tricky.. But definitely nothing that requires puling three motor. Pulling the ac compressor loose from its bracket helps. Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	Anybody try to install Ash's inlet planar piping with the - fuzzymonkey 15:58:18 12/06/11 You're kidding right? - samsungZ (Houston) 16:14:00 12/06/11 Settle down all ready. - Bernie (NoVA) 16:21:18 12/06/11 The Big B man, been awhile... - samsungZ (Houston) 16:24:40 12/06/11 Not much has changed with you either it seems... (n/m) - Aqualung 18:32:17 12/06/11 *an - new2boost 17:25:37 12/06/11 A few times.... - Ash's Z 16:17:10 12/06/11 What kind of gains can be expected on a stock/SP500 turbo? (n/m) - madscientist222 17:35:30 12/06/11 Nick's got mail ... (n/m) - ConVerTT 20:21:05 12/06/11 With BDE low profile mounts it is really easy........ - Greg D. (Specialty-Z) 17:12:34 12/06/11 Greg...question - new2boost 17:32:13 12/06/11 Well.......... - Greg D. (Specialty-Z) 18:11:21 12/06/11 I also ducted air from under the car to feed the radiator - Greg D. (Specialty-Z) 18:17:39 12/06/11 What about Deans car? Does he drive on the street much? - Boosted1 18:33:53 12/06/11 Dean drives his car every day, he does not have A/C - Greg D. (Specialty-Z) 19:49:34 12/06/11 are we talking about grinding a bit of the motor mounts? (n/m) - fuzzymonkey 18:33:45 12/06/11 Correct (n/m) - Greg D. (Specialty-Z) 19:50:41 12/06/11 Damn it - Broke_as_**** 20:40:08 12/06/11 Thanks for the clarification - I typed my response in on my - Ash's Z 09:25:56 12/07/11 Difficult in my opinion... - ZonaZ 19:14:52 12/06/11 The indents in the stock pipes are the reason why I want to - Greg D. (Specialty-Z) 20:03:40 12/06/11 Is it fair to say it might be faster for most to just pull - ConVerTT 20:18:08 12/06/11 That's what I ultimately decided to do. The problem with - Wright (Ca) 20:28:11 12/06/11 I think you were looking for an excuse to do more :-P (n/m) - Greg D. (Specialty-Z) 20:36:54 12/06/11 Not in my opinion, for me it is a reasonable job to do - Greg D. (Specialty-Z) 20:35:23 12/06/11 if you're installing BDE motor mounts as well, yes. (n/m) - vorpalZ 09:49:13 12/07/11 +1 on every point. (n/m) - Stadsport (PHX) 21:53:52 12/06/11
Post a Followup	You cannot reply to this message because you are not logged in.