Subject	Yo
Posted by	Broke_as_**** on November 28, 2011 at 6:24 PM
	This message has been viewed 156 times.
In Reply To	will you elaborate on "checking runout" (n/m) posted by Madhatter10-6 on November 28, 2011 at 03:09 PM
Message	[ http://www.300zx-twinturbo.com/cgi-bin/manual.cgi?list=pd&dir=&config=&refresh=&direction=forward&scale=0&cycle=off&slide=7&design=default&total=43 ]
Follow Ups	Best place to buy a one piece driveshaft for less? - sonnymarton 23:57:00 11/27/11 Got mine from Mitch@Epracing for cheapest I think. (n/m) - Z32TT-R 02:16:31 11/28/11 2nd... (n/m) - BlitZ91TT 10:51:08 11/28/11 He's building me a new driveshaft with the cv joint from my - Wright (Ca) 11:40:06 11/28/11 Shaftmasters was resonable. No issues on high hp Z (n/m) - XTZ 03:00:52 11/28/11 It's not an upgrade. Some one-piece ds's are close to - zellamay 11:16:37 11/28/11 true, but they are loads easier to handle when under the car (n/m) - LJZTT 11:53:34 11/28/11 Besides NVH, what is the downgrade aspect of it? (n/m) - BigTDogg (MA) 12:08:25 11/28/11 Yep. gave mine up for an OEM, getting a CF soon (n/m) - ZiNnYc 12:30:44 11/28/11 Not an upgrade because of balance issues alone? Or... - Jayru 15:40:14 11/28/11 The gain due to less rotational mass is almost nil, - zellamay 19:53:02 11/28/11 True, the rotational weight loss effect is minimal to nil - BigTDogg (MA) 09:12:56 11/29/11 18 lbs is a lot, and these cars are too darn heavy. - zellamay 10:29:35 11/29/11 Happy with my Powertrain Aluminum from IPP. (n/m) - PiotrC70 11:38:24 11/28/11 2nd (n/m) - BigTDogg (MA) 12:08:37 11/28/11 I went with a rebuilt OEM, smooth as butta but not cheap. (n/m) - BoneZ (MD) 13:03:20 11/28/11 I have put Z1 platinum on several Z's and really like them (n/m) - Madhatter10-6 13:44:36 11/28/11 2nd... check your runout when installing - vorpalZ 13:54:55 11/28/11 Maybe. I'm glad that was your experience, but many - zellamay 14:36:58 11/28/11 my experience is that most people don't check runout (n/m) - vorpalZ 14:41:00 11/28/11 will you elaborate on "checking runout" (n/m) - Madhatter10-6 15:09:40 11/28/11 Yo - Broke_as_**** 18:24:30 11/28/11 thank you sir! (n/m) - Madhatter10-6 19:01:18 11/28/11 If there is one thing that everyone should do - Broke_as_**** 19:32:49 11/28/11 Vibrations were seen at >100mph or so...cant remember the - ZiNnYc 20:17:49 11/28/11
Post a Followup	You cannot reply to this message because you are not logged in.