Subject	There is an *absolute* difference between *redrilled* and
Posted by	CoHPhasor on November 14, 2011 at 11:26 PM
	This message has been viewed 446 times.
In Reply To	AFAIK, anything over stock flowrate is drilled. (n/m) posted by BigTDogg (MA) on November 14, 2011 at 10:41 AM
Message	*drilled* First off, *ALL* injectors are "drilled", unless you use a water jet. The difference is that a manufacturer that uses a 100% QA'ed good injector actually pays attention to what they are doing, does real R&D work and has a consistent product. redrills are all kinds of fucked up. inconsistent drilling angles/sizes, lack of deburring as shown in the OP's photo, and just as bad - lackluster flow-matching. Get injectors from a reputable manufacturer, always, period. Going side feed? Nismo Going top feed? Injector Dynamics Everything else is a crapshoot.
Follow Ups	Redrilled injectors suck! - hunterg 23:42:21 11/13/11 Little behind are we? (n/m) - new2boost 00:08:08 11/14/11 Who knew ? (n/m) - ConVerTT 01:00:05 11/14/11 Here's what Jim Wolf has to say about them - BlackholeZ 02:41:22 11/14/11 are all Deatshwerks injectors drilled? - BOOZT_JUNKIE 07:10:18 11/14/11 Yes (n/m) - BigTDogg (MA) 08:22:52 11/14/11 crap. will check & see if i can return them. - BOOZT_JUNKIE 08:49:12 11/14/11 are you sure? i had heard they were making new now. (n/m) - Antihero 10:01:53 11/14/11 Sure the injector is new and not a used core but either way - nissanguyz32 10:06:25 11/14/11 AFAIK, anything over stock flowrate is drilled. (n/m) - BigTDogg (MA) 10:41:47 11/14/11 There is an *absolute* difference between *redrilled* and - CoHPhasor 23:26:08 11/14/11 Also laser drilling and EDM (n/m) - Jim (Selin Design) 23:58:47 11/14/11 Yep, I should have been more specific, for the nitpickers :P - BigTDogg (MA) 08:24:24 11/15/11 you are wrong. - Antihero 11:08:56 11/15/11 Right, but the ones CZP sell are garbage - BigTDogg (MA) 14:46:08 11/15/11 ive installed about 100 dw injectors, some with ohm - Dane (Houston) 11:01:07 11/14/11 good to know. i may try the ones i have... (n/m) - BOOZT_JUNKIE 11:39:34 11/14/11 No - RobZ32 12:36:37 11/14/11 JECS are bored also. (n/m) - z-u-later 13:28:12 11/14/11 Where are you guys getting your info? JECS is OEM. - Antihero 11:17:29 11/15/11 Here. - Evan(CA) 14:01:33 11/15/11 Interesting advertizing....... - Greg D. (Specialty-Z) 20:13:06 11/15/11 Oh, and I wouldn't trust much of what Z1 says, FWIW (n/m) - BigTDogg (MA) 09:29:21 11/16/11 Venom? (n/m) - BigTDogg (MA) 13:28:54 11/14/11 Five-O Motorsports? (n/m) - Wright (Ca) 14:02:00 11/14/11 Age of that injector? (n/m) - BoneZ (MD) 07:58:07 11/14/11 About 3 yrs (n/m) - hunterg 10:39:49 11/14/11 Redrilled injectors don't have to suck. Remember, the - zellamay 11:17:14 11/14/11 Flow testing measuring peak flow is useless - BigTDogg (MA) 11:54:56 11/14/11 Big difference between drilling at the OEM and aftermarket - BlackholeZ 17:31:56 11/14/11 So, it's not possible to take them apart, drill them, - zellamay 18:43:25 11/14/11 No, they are welded, and the plastic is cast around that. - BlackholeZ 20:17:16 11/14/11
Post a Followup	You cannot reply to this message because you are not logged in.