Subject	Big difference between drilling at the OEM and aftermarket
Posted by	BlackholeZ on November 14, 2011 at 5:31 PM
	This message has been viewed 459 times.
In Reply To	Redrilled injectors don't have to suck. Remember, the posted by zellamay on November 14, 2011 at 11:17 AM
Message	stock injectors were not drilled on the assembled injector. Holes are drilled using the right tooling that doesn't leave a mess or damage the pintle. If an injector is not properly atomizing the fuel, the engine will not be able to burn it, it doesn't matter if you map the flow rates. Using drilled injectors is like using a monkey wrench on your car. They make the right tool, use it. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Redrilled injectors suck! - hunterg 23:42:21 11/13/11 Little behind are we? (n/m) - new2boost 00:08:08 11/14/11 Who knew ? (n/m) - ConVerTT 01:00:05 11/14/11 Here's what Jim Wolf has to say about them - BlackholeZ 02:41:22 11/14/11 are all Deatshwerks injectors drilled? - BOOZT_JUNKIE 07:10:18 11/14/11 Yes (n/m) - BigTDogg (MA) 08:22:52 11/14/11 crap. will check & see if i can return them. - BOOZT_JUNKIE 08:49:12 11/14/11 are you sure? i had heard they were making new now. (n/m) - Antihero 10:01:53 11/14/11 Sure the injector is new and not a used core but either way - nissanguyz32 10:06:25 11/14/11 AFAIK, anything over stock flowrate is drilled. (n/m) - BigTDogg (MA) 10:41:47 11/14/11 There is an *absolute* difference between *redrilled* and - CoHPhasor 23:26:08 11/14/11 Also laser drilling and EDM (n/m) - Jim (Selin Design) 23:58:47 11/14/11 Yep, I should have been more specific, for the nitpickers :P - BigTDogg (MA) 08:24:24 11/15/11 you are wrong. - Antihero 11:08:56 11/15/11 Right, but the ones CZP sell are garbage - BigTDogg (MA) 14:46:08 11/15/11 ive installed about 100 dw injectors, some with ohm - Dane (Houston) 11:01:07 11/14/11 good to know. i may try the ones i have... (n/m) - BOOZT_JUNKIE 11:39:34 11/14/11 No - RobZ32 12:36:37 11/14/11 JECS are bored also. (n/m) - z-u-later 13:28:12 11/14/11 Where are you guys getting your info? JECS is OEM. - Antihero 11:17:29 11/15/11 Here. - Evan(CA) 14:01:33 11/15/11 Interesting advertizing....... - Greg D. (Specialty-Z) 20:13:06 11/15/11 Oh, and I wouldn't trust much of what Z1 says, FWIW (n/m) - BigTDogg (MA) 09:29:21 11/16/11 Venom? (n/m) - BigTDogg (MA) 13:28:54 11/14/11 Five-O Motorsports? (n/m) - Wright (Ca) 14:02:00 11/14/11 Age of that injector? (n/m) - BoneZ (MD) 07:58:07 11/14/11 About 3 yrs (n/m) - hunterg 10:39:49 11/14/11 Redrilled injectors don't have to suck. Remember, the - zellamay 11:17:14 11/14/11 Flow testing measuring peak flow is useless - BigTDogg (MA) 11:54:56 11/14/11 Big difference between drilling at the OEM and aftermarket - BlackholeZ 17:31:56 11/14/11 So, it's not possible to take them apart, drill them, - zellamay 18:43:25 11/14/11 No, they are welded, and the plastic is cast around that. - BlackholeZ 20:17:16 11/14/11
Post a Followup	You cannot reply to this message because you are not logged in.