Subject	1st of all, good move.
Posted by	ZiNnYc on October 28, 2011 at 4:19 PM
	This message has been viewed 181 times.
In Reply To	What are members with larger smic's doing to fix this ? posted by Xteam300TT (South Tx ) on October 28, 2011 at 04:07 PM
Message	secondly, there are a few options. Summit Racing has a few plastic overflows. I opted for a billet solution. As far as mounting solutions, you can 1) mount in the stock location using the stock bolt hole. It will be flush against the chassis, (mirrored solution on pass side) 2) hang remotely on the fender bracket (this arm that sticks out to hold your splash guard) 3) under the center panel tucked away in a corner. The stock overflow hose will fit the hose barb fitting that ships with these type of tanks, so its essentially a plug n play solution. I went through Canton Racing to match the blue theme https://www.cantonracingproducts.com/cgi-bin/commerce.cgi?preadd=action&key=80-250 but any Summit Racing generic will do. Make sure you use sealer on any NPT plug, and stick with galvanized bolts for mounting.
Follow Ups	What are members with larger smic's doing to fix this ? - Xteam300TT (South Tx ) 16:07:31 10/28/11 Re: What are members with larger smic's doing to fix this ? - Stadsport (PHX) 16:17:39 10/28/11 I dont think you should be going through a quart of overflow (n/m) - ZiNnYc 16:21:58 10/28/11 1st of all, good move. - ZiNnYc 16:19:41 10/28/11 Thanx , any pics available in the various locations ? (n/m) - Xteam300TT (South Tx ) 16:28:42 10/28/11 Someone else might be able to help you out with pics - ZiNnYc 16:33:31 10/28/11 I can post a pic later of my plastic tank. Just installed. (n/m) - evan_aggie(ATX) 16:38:45 10/28/11 great , thanx ! (n/m) - Xteam300TT (South Tx ) 16:49:38 10/28/11 I may decide to move it, but for now, here is what I planned - evan_aggie(ATX) 18:53:42 10/28/11 ^^^^^This is the correct lacation and most sensible - TTZEDHEAD 22:55:26 10/28/11 That location obstructs the IC pipe routing. (n/m) - Bernie (NoVA) 11:55:23 10/29/11 How do you plan on connecting the intercooler - Sly 07:22:59 10/29/11 moroso overflow tank - timmaz 18:21:13 10/28/11 That's kind of cool... would you do it again? (n/m) - thumper 21:21:46 10/28/11 Exactly my setup and location (n/m) - HighPsi (NorCal) 20:57:05 10/29/11 You don't really have to do anything about it... - Bernie (NoVA) 21:07:38 10/28/11 2nd (n/m) - Woody75 (Denver) 17:55:56 10/29/11 yup, deleted CC, removed hard lines, Massives fit fine - vorpalZ 22:52:13 10/29/11 You can mount the overflow tank anywhere, doesn't have - zellamay 21:36:39 10/28/11 I installed the same setup as evanaggie. - 1911a1 22:00:27 10/28/11 I used some expanded stainless. - MPV TT 23:32:41 10/28/11
Post a Followup	You cannot reply to this message because you are not logged in.