Subject	As BlackholeZ stated the purpose of this kit to allow
Posted by	sfarrah on September 23, 2011 at 9:28 PM
	This message has been viewed 181 times.
In Reply To	For people like Kuah posted by BlackholeZ on September 23, 2011 at 06:05 PM
Message	wider wheels and tires as well as serve an aerodynamic purpose while being lightweight and strong. Along with the vents at the back of the front fenders there will also be vent inserts for the top of the fender that will release the high pressure air that builds up inside the wheel well.
Follow Ups	Sneak Peek - SPL Parts dry carbon fiber widebody - sfarrah 14:59:05 09/23/11 hmmm... (n/m) - ForceFedTT (SoCal) 15:04:09 09/23/11 Re: Sneak Peek - SPL Parts dry carbon fiber widebody - c300zxtt 15:07:29 09/23/11 initial estimates are $4-5k. - sfarrah 16:09:31 09/23/11 Damniiiit ..... I wont be getting 2 any longer . Iv seen a - xteam300tt 17:38:36 09/23/11 Compare these prices to other sources for dry carbon fiber - sfarrah 21:21:41 09/23/11 I see your point so why doesnt someone make them - xteam300tt 22:18:28 09/23/11 the Evil Twin gets even more evil. (n/m) - Tu 15:09:27 09/23/11 Yes, it certainly does. Can't wait to get it back and on - sfarrah 16:12:25 09/23/11 Certainly gets down to the business end of things (n/m) - Red Hawk (CO) 15:29:49 09/23/11 CF nose panel - ArubaDave 15:35:52 09/23/11 I am gonna start saving my pennies!!! (n/m) - new2boost 15:36:58 09/23/11 Ill take two ! - xteam300tt 15:38:34 09/23/11 Sexy. (n/m) - Dallas DamonZ 16:34:31 09/23/11 Nice. This means you'll need new wheels again? (n/m) - Karl (MD) 16:47:50 09/23/11 With the ARP wheel studs I can safely run spacers but - sfarrah 19:31:04 09/23/11 Nice! Great to see SPL still bringing great products to - TheTwinZ (Peru) 17:33:21 09/23/11 Where can I get a twinz design p-spec front fascia ? - xteam300tt 17:51:20 09/23/11 Looks like high quality parts! - sedative 17:36:23 09/23/11 For people like Kuah - BlackholeZ 18:05:07 09/23/11 As BlackholeZ stated the purpose of this kit to allow - sfarrah 21:28:18 09/23/11 nice (n/m) - aliaZ 19:29:54 09/23/11 Nice! Get them patented/copyrighted so AMS doesn't steal it - zfreak(Dallas) 20:00:07 09/23/11 lol, I'd like to see AMS try (n/m) - zgene4 20:36:53 09/23/11 Except it would be made from cardboard fiber (n/m) - MrOzzie5183 21:11:27 09/23/11 LOL...good one! (n/m) - The Hawk 12:15:20 09/25/11 Man gives me the reason for full body paint again!!! (n/m) - Z ONLY1 21:34:21 09/23/11 When is somebody going to do full wide rear quarter panels? (n/m) - Z32TT-R 22:08:07 09/23/11 can't wait to see it painted (n/m) - FuerGrissa 22:20:44 09/23/11 Any estimates on when this will be available? (n/m) - spdrmn15 01:33:15 09/24/11 better start stock piling copper now... (n/m) - zgene4 22:31:16 09/24/11 cool! (n/m) - KongZTT GT28RS MD 20:02:18 09/24/11 Too bad the rear bumper is going to limit sizing - ArticDragon192 16:48:59 09/25/11
Post a Followup	You cannot reply to this message because you are not logged in.