Subject	For people like Kuah
Posted by	BlackholeZ on September 23, 2011 at 6:05 PM
	This message has been viewed 687 times.
In Reply To	Looks like high quality parts! posted by sedative on September 23, 2011 at 05:36 PM
Message	they are purposely built to fit bigger wheels/tires and heve them fith w/o scrubbing without having to do stupid shit to the suspension geometry. Very common among euro touring cars. vs -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Sneak Peek - SPL Parts dry carbon fiber widebody - sfarrah 14:59:05 09/23/11 hmmm... (n/m) - ForceFedTT (SoCal) 15:04:09 09/23/11 Re: Sneak Peek - SPL Parts dry carbon fiber widebody - c300zxtt 15:07:29 09/23/11 initial estimates are $4-5k. - sfarrah 16:09:31 09/23/11 Damniiiit ..... I wont be getting 2 any longer . Iv seen a - xteam300tt 17:38:36 09/23/11 Compare these prices to other sources for dry carbon fiber - sfarrah 21:21:41 09/23/11 I see your point so why doesnt someone make them - xteam300tt 22:18:28 09/23/11 the Evil Twin gets even more evil. (n/m) - Tu 15:09:27 09/23/11 Yes, it certainly does. Can't wait to get it back and on - sfarrah 16:12:25 09/23/11 Certainly gets down to the business end of things (n/m) - Red Hawk (CO) 15:29:49 09/23/11 CF nose panel - ArubaDave 15:35:52 09/23/11 I am gonna start saving my pennies!!! (n/m) - new2boost 15:36:58 09/23/11 Ill take two ! - xteam300tt 15:38:34 09/23/11 Sexy. (n/m) - Dallas DamonZ 16:34:31 09/23/11 Nice. This means you'll need new wheels again? (n/m) - Karl (MD) 16:47:50 09/23/11 With the ARP wheel studs I can safely run spacers but - sfarrah 19:31:04 09/23/11 Nice! Great to see SPL still bringing great products to - TheTwinZ (Peru) 17:33:21 09/23/11 Where can I get a twinz design p-spec front fascia ? - xteam300tt 17:51:20 09/23/11 Looks like high quality parts! - sedative 17:36:23 09/23/11 For people like Kuah - BlackholeZ 18:05:07 09/23/11 As BlackholeZ stated the purpose of this kit to allow - sfarrah 21:28:18 09/23/11 nice (n/m) - aliaZ 19:29:54 09/23/11 Nice! Get them patented/copyrighted so AMS doesn't steal it - zfreak(Dallas) 20:00:07 09/23/11 lol, I'd like to see AMS try (n/m) - zgene4 20:36:53 09/23/11 Except it would be made from cardboard fiber (n/m) - MrOzzie5183 21:11:27 09/23/11 LOL...good one! (n/m) - The Hawk 12:15:20 09/25/11 Man gives me the reason for full body paint again!!! (n/m) - Z ONLY1 21:34:21 09/23/11 When is somebody going to do full wide rear quarter panels? (n/m) - Z32TT-R 22:08:07 09/23/11 can't wait to see it painted (n/m) - FuerGrissa 22:20:44 09/23/11 Any estimates on when this will be available? (n/m) - spdrmn15 01:33:15 09/24/11 better start stock piling copper now... (n/m) - zgene4 22:31:16 09/24/11 cool! (n/m) - KongZTT GT28RS MD 20:02:18 09/24/11 Too bad the rear bumper is going to limit sizing - ArticDragon192 16:48:59 09/25/11
Post a Followup	You cannot reply to this message because you are not logged in.