Subject	Awesome job!
Posted by	Motormutt (SATX) on September 23, 2011 at 9:37 AM
	This message has been viewed 99 times.
In Reply To	Recent build I feel like sharing posted by Tech@EPR on September 23, 2011 at 08:26 AM
Message	I need to strip down my block soon so that we can start a rebuild.
Follow Ups	Recent build I feel like sharing - Tech@EPR 08:26:33 09/23/11 Nice! (n/m) - Rob'Z 08:38:59 09/23/11 No thermostat? (n/m) - Woody75 (Denver) 08:41:24 09/23/11 I was just thinking the same... Where's the thermostat - MixManMash 10:25:34 09/23/11 Re: No thermostat? - Tech@EPR 11:51:18 09/23/11 How is that??? Never tried but seems like there is no room. (n/m) - TTNIckdizzle 13:40:00 09/23/11 With the timing cover back plates out of the way, it's not - Dave N 13:52:40 09/23/11 I did mine with the lower plenum in place. (n/m) - BoneZ (MD) 19:40:32 09/23/11 Informative. (n/m) - spicyZ 09:16:29 09/23/11 Awesome job! - Motormutt (SATX) 09:37:59 09/23/11 Re: Recent build I feel like sharing - tjcaustin 10:27:15 09/23/11 Re: Re: Recent build I feel like sharing - Tech@EPR 11:52:02 09/23/11 You might want to ask around first... - ni[X]it 12:13:10 09/23/11 :/ (n/m) - thumper 13:29:42 09/23/11 Re: You might want to ask around first... - Tech@EPR 18:59:09 09/24/11 clean (n/m) - Adam (NoVA) 10:37:43 09/23/11 What was the diagnosis on the prior engine failure? - aliaZ 11:03:23 09/23/11 Re: What was the diagnosis on the prior engine failure? - Tech@EPR 11:49:56 09/23/11 Lol, it's not like people come to you because - na300zx (OH) 14:09:46 09/23/11 Re: Lol, it's not like people come to you because - Tech@EPR 15:12:40 09/23/11 of course its silly to not share in a thread you start about - Adam (NoVA) 17:33:04 09/23/11 Hey every little counts towards trying to be the best lol (n/m) - Red Hawk (CO) 14:35:12 09/23/11 nice work (n/m) - Madhatter10-6 11:03:34 09/23/11 I'd like to see a side by side photo of rods, one coated - zgene4 11:26:38 09/23/11 Re: I'd like to see a side by side photo of rods, one coated - Tech@EPR 11:54:22 09/23/11 Considering the size ratio of the rods to the crank, is - SlicktopTT 12:11:44 09/23/11 Re: Considering the size ratio of the rods to the crank, is - Tech@EPR 12:37:22 09/23/11 What type of application is this motor for street or strip? - TTNIckdizzle 13:36:40 09/23/11 Re: What type of application is this motor for street or strip? - Tech@EPR 15:16:17 09/23/11 Awesome! That makes - Ziceman(East TN) 14:56:23 09/23/11 Lookin good Mitch. (n/m) - Z32TT-R 22:27:59 09/23/11 Clean work space, organized assembly protocol. Nice. (n/m) - Gordo 93TT Daytona 10:34:00 09/24/11
Post a Followup	You cannot reply to this message because you are not logged in.