Subject	Glad to hear. Charles is a great guy with solid products. (n/m)
Posted by	rojoloco (San Diego) on September 02, 2011 at 11:00 PM
	This message has been viewed 154 times.
In Reply To	Just got off the phone with Charles at Powertrix. posted by tbarnett on September 02, 2011 at 12:36 PM
Message
Follow Ups	I'm not a doctor but I feel like something is wrong here. - tbarnett 23:49:17 09/01/11 What brand was that? (n/m) - FuerGrissa 00:26:20 09/02/11 Powertrix (n/m) - tbarnett 00:55:20 09/02/11 Yikes, thats not good, how many miles were on those? - Z32TT-R 03:04:29 09/02/11 I'd have to check to be sure, but I think about 20k. (n/m) - tbarnett 08:38:37 09/02/11 Curious if they came out of the same factory as these - Gennosuke 06:12:01 09/02/11 looks like a design issue - johnathanbarnes 13:41:10 09/02/11 Not Powertrix adjustable Tension rods - njz 00:30:10 09/02/11 Defective part or poor quality? (n/m) - rojoloco (San Diego) 00:38:30 09/02/11 Yikes, that's a little scary. That'd toss you off the road - schuss 00:43:40 09/02/11 Wow! What are you going to replace them with? (n/m) - Evan(CA) 01:50:09 09/02/11 that's a good question - aliaZ 08:01:21 09/02/11 This prompted me to go to SPL's site, but I am not seeing - jmt-z 09:57:51 09/02/11 try emailing him - aliaZ 10:44:25 09/02/11 Im not in the market to buy, I was just curious. (n/m) - jmt-z 12:12:54 09/02/11 He doesn't carry them anymore as far as I know. - rojoloco (San Diego) 22:50:44 09/02/11 eh...I don't think so - aliaZ 08:40:12 09/03/11 I believe the old SPL's are the same in that area. - rojoloco (San Diego) 10:45:32 09/03/11 after looking at the pictures again - aliaZ 17:10:19 09/03/11 You are partially correct. - rojoloco (San Diego) 19:16:57 09/04/11 By saying that I am partially correct, you are insinuating - aliaZ 22:13:47 09/05/11 Please stop posting information you don't know for a fact - kuah@splparts.com 15:00:52 09/06/11 wow (n/m) - aliaZ 05:42:15 09/02/11 Re: I'm not a doctor but I feel like something is wrong here. - MaxxAction 07:48:53 09/02/11 Perhaps your defective units can be replaced like the OP's (n/m) - jschrauwen 11:24:05 09/03/11 I assume the car is lowered? How much? - Woody75 (Denver) 08:05:08 09/02/11 Take a look at this... - Jayru 08:43:27 09/02/11 Yes, look here. An extended center section is the solution. - Gordo 93TT Daytona 09:11:20 09/02/11 I used my spl's with the 300* kit so they wouldn't have - na300zx (OH) 09:55:19 09/02/11 Good to know! - Jayru 11:06:18 09/02/11 Not too long. No issues though - na300zx (OH) 22:02:17 09/02/11 Yea. I actually saw that while looking around last - tbarnett 09:14:39 09/02/11 You are correct about their design change. - rojoloco (San Diego) 22:55:58 09/02/11 Those are the older versions...wonder if those max extension - Wright (Ca) 09:32:52 09/02/11 Common sense should be applied for some things though - Woody75 (Denver) 09:40:35 09/02/11 Eh, I agree. But that's a pretty gray area right there. - dogpile 09:49:50 09/02/11 i agree with dogpile (n/m) - ForceFedTT (SoCal) 14:48:48 09/02/11 And MacDonalds was wrong for not warning about fat content. - rojoloco (San Diego) 22:58:57 09/02/11 not an apples apples comparison - LJZTT 09:36:32 09/03/11 Then the blame still falls on the consumer. - rojoloco (San Diego) 10:51:50 09/03/11 Guess you missed the "I agree" part? - dogpile 16:33:43 09/03/11 I can see your point. (n/m) - rojoloco (San Diego) 17:22:25 09/03/11 those don't look like powertrix to me (n/m) - moxie (SF) 10:32:06 09/02/11 Just got off the phone with Charles at Powertrix. - tbarnett 12:36:47 09/02/11 thats good to hear hes taking care of it. (n/m) - Z32TT-R 14:18:10 09/02/11 Glad to hear. Charles is a great guy with solid products. (n/m) - rojoloco (San Diego) 23:00:21 09/02/11 class act, and this is where some may suggest 300Degree - jzx 17:46:21 09/03/11
Post a Followup	You cannot reply to this message because you are not logged in.