Subject	You might want to flip your timing gun pick up 180deg.
Posted by	Bernie (NoVA) on August 23, 2011 at 9:59 AM
	This message has been viewed 113 times.
In Reply To	mine is cocked all the way to one side too posted by LJZTT on August 23, 2011 at 08:05 AM
Message	And test again. CAS should be middle-ish for 15degrees Bernie Bilski berniebilski@cox.net 1995 Nissan 300ZX TwinTurbo in Cobalt Green 1997 Nissan 240SX SE in Ultra Red ZCCNV #390 ~ ECZA #368
Follow Ups	Closer to being ready for the SZ dyno day. - Woody75 (Denver) 22:27:50 08/22/11 Glad to see it all in one piece. Will you be spraying blue - zgene4 23:07:54 08/22/11 Boost juice. (n/m) - Woody75 (Denver) 07:50:13 08/23/11 elitist - zgene4 09:30:54 08/23/11 Looks good Tim. I might swing by the dyno if I get a chance. (n/m) - ShakaShaun(Denver) 23:08:03 08/22/11 Shoot me a text tomorrow also check your email shortly. (n/m) - 5280Z_nightstalker 23:15:27 08/22/11 Looks good - I'll be there this weekend (n/m) - Tikigod (Denver) 23:27:08 08/22/11 Good stuff Tim, thanks.. - ttz'in (NorCal) 23:28:54 08/22/11 clean across the board! :) (n/m) - samsungz 23:35:21 08/22/11 Good luck. (n/m) - Bernie (NoVA) 00:40:23 08/23/11 beautiful Z (n/m) - aliaZ 05:28:00 08/23/11 Nice work. Looking forward to seeing your results. - Boosted1 06:12:10 08/23/11 Yeah, things are usually that way. - Woody75 (Denver) 07:56:16 08/23/11 When I upgraded to a 95 harness and CAS, my CAS - na300zx (OH) 06:48:02 08/23/11 I'm not too concerned with it. - Woody75 (Denver) 07:54:28 08/23/11 mine is cocked all the way to one side too - LJZTT 08:05:00 08/23/11 Yes...higher idle=advanced timing... - 90GoldZ 09:42:13 08/23/11 You might want to flip your timing gun pick up 180deg. - Bernie (NoVA) 09:59:58 08/23/11 yeah, this is an issue - LJZTT 13:07:56 08/23/11 Mine 3, but then SZ fixed it whilist on the dyno. - BigTDogg (MA) 10:24:03 08/23/11 And details as to what they did? (n/m) - Woody75 (Denver) 10:25:58 08/23/11 They fixed it... - BigTDogg (MA) 10:35:15 08/23/11 Ok. I've flipped and checked mine from both locations. - Woody75 (Denver) 10:38:03 08/23/11 You may be off a tooth then. (n/m) - Bernie (NoVA) 10:42:41 08/23/11 It would have jumped then when I got it started. - Woody75 (Denver) 10:56:48 08/23/11 Some things to share...... - Greg D. (Specialty-Z) 19:45:05 08/23/11 Looks nice. Good luck! (n/m) - TheTwinZ (Peru) 09:34:16 08/23/11 Looking good Woody, GL on the dyno day. (n/m) - 90GoldZ 09:42:57 08/23/11 Have fun... give our regards to the SZ crew - vorpalZ 09:48:35 08/23/11 Oh you know, it will be the usual crap... - Woody75 (Denver) 10:02:20 08/23/11 chuckle (n/m) - vorpalZ 10:39:26 08/23/11 Your so cynical. - coma_ass 13:22:55 08/23/11 Simple solution. Post corrected and uncorrected dyno's - ztunerz 14:36:24 08/23/11 ...and then people kvetch about the type of dyno - vorpalZ 15:06:29 08/23/11 2nd. It'll be a fun weekend! (n/m) - MixManMash 17:41:32 08/23/11 Glad everything worked out for you... (n/m) - Zski 09:52:18 08/23/11 Thanks for the pics. (n/m) - Woody75 (Denver) 10:13:08 08/23/11 No Problem... Glad I was able to help out... (n/m) - Zski 10:16:43 08/23/11 Lookin good sir! Hope you're happy with the pipes! (n/m) - Nick (ASH-SPEC) 11:07:47 08/23/11 It is much better to put the WI ports right at the TBs - Ash's Z 11:22:00 08/23/11 I agree. I had my old nozzles at the tb. - Woody75 (Denver) 11:45:54 08/23/11 Good luck with the tuning day! We have done numerous ones - Piranha 18:57:07 08/23/11 Good luck on your results. You look well prepared. (n/m) - Inzane 11:37:34 08/24/11
Post a Followup	You cannot reply to this message because you are not logged in.