Subject	If your MAF signal is reading 0.08 if revving or underload
Posted by	BigTDogg (MA) on July 29, 2011 at 9:23 AM
	This message has been viewed 127 times.
In Reply To	Thanks Barry. (n/m) posted by arrowenterprises on July 29, 2011 at 05:38 AM
Message	Then you MAF/translator is bad. "I'm glad I have the MSP mani's." - jschrauwen 22:20:13 06/10/08 "...Downpipes own. They own everything...anything...all there ever was and will be...they should be stock on all cars. Screw the environment, emissions, noise! I love them...I shall name my first-born after them with glee..." - SeedyRom 05:13:20 10/03/02 "i love the cock" - genic 22:20:47 09/25/03 "I hope you get fucked in the ass with a pringles can." - ni[X]it 14:53:53 02/02/06 "Either ignore him or beat him up. Anything else will be over his head." - Marshall 12:28:23 08/18/04 "i've got to the point where i can drive the Z at its limits and i want more" - shadowZ 16:29:56 08/31/04 "I was way more timid then than I am now about getting in there and yanking on things." - TT XTZ 13:30:34 07/25/05 "Just ran out to get some knee pads. I'm ready now... BRING.....IT.....ON... :-) " - Dave N 19:04:30 10/31/07
Follow Ups	Diagnosing a bad MAF in a Selin Dual MAF setup. - MixManMash 15:54:43 07/28/11 Its your drivers side then (n/m) - Z32TT-R 16:11:22 07/28/11 Try swapping the sensors left to right and repeat - Jim (Selin Design) 16:20:54 07/28/11 Hi Jim, I've never had any issues prior to this event. - MixManMash 16:50:30 07/28/11 The planar set-up should not influence or affect - JMartz 16:28:33 07/28/11 My ECU is set up for Dual MAF. - MixManMash 16:52:24 07/28/11 I'm having exactly the same problem right now!... - arrowenterprises 17:14:25 07/28/11 Sounds like either your MAF or your MAF wiring. - MixManMash 17:25:33 07/28/11 Hoping it's not # 34. (n/m) - arrowenterprises 18:32:13 07/28/11 34 will definitely not cause idling issues. (n/m) - MixManMash 08:02:09 07/29/11 Shoot me an email and I'll help you get it sorted out (n/m) - Jim (Selin Design) 18:57:41 07/28/11 Check the value of the MAF signal with Datascan/Nistune - BigTDogg (MA) 20:03:00 07/28/11 the ink on my "newbie" t-shirt is still wet so I won't ask.. - arrowenterprises 20:22:27 07/28/11 If you plug a blazt or other diagnostic cable into the port - Barry (NJ) 21:19:11 07/28/11 Thanks Barry. (n/m) - arrowenterprises 05:38:57 07/29/11 If your MAF signal is reading 0.08 if revving or underload - BigTDogg (MA) 09:23:14 07/29/11 Check your bovs for leaking first (n/m) - ztunerz 20:30:06 07/28/11 They are plumbed in as recircs. Definitely not leaking. (n/m) - MixManMash 21:49:35 07/28/11 Do you have HID's? There was a big thread on 3zc - supermario680 07:56:05 07/29/11 Yes I do, but how can they only now be causing an issue? - MixManMash 08:01:03 07/29/11 Then it's probably not related.. - supermario680 08:25:16 07/29/11 Resolved: Driver's side MAF was bad. - MixManMash 16:03:33 07/29/11
Post a Followup	You cannot reply to this message because you are not logged in.