Subject	I would have gladly paid extra for some well made
Posted by	JMartz on June 08, 2011 at 3:22 PM
	This message has been viewed 114 times.
In Reply To	Versus the 300 degree kit. posted by BigTDogg (MA) on June 08, 2011 at 03:13 PM
Message	parts. Had no idea Z1 and others made this cheap stamped crap and not tell you about it. The gasket that comes in the kit is over a 1/16 of an inch thick so I don't believe you would have to overtighten the screws to get it to seal. Than being said crap is crap, no way arouund it. Wish these businesses were more explicit about their products. I'm on this forum all the time and had never encoountered this discussion. You can be sure I would have never gone with substandard materials knowingly.
Follow Ups	The operation was a success! - JMartz 09:34:28 06/08/11 What kit did you use? Or did you just fab something? (n/m) - new2boost 10:40:27 06/08/11 I used the Z1 kit but I would not recommend it. - JMartz 10:48:05 06/08/11 Great..I just bought that kit last week for my EGR delete.. (n/m) - new2boost 10:54:33 06/08/11 Return it and Get the 300Degree one from Kyle@IPP (n/m) - Zski 10:56:11 06/08/11 2nd. (n/m) - zfreak(Dallas) 16:37:17 06/08/11 Zero issues with the Z1 kit I've used - Gennosuke 11:42:13 06/08/11 The Z1 kit is perfectly functional. - JMartz 13:21:01 06/08/11 All that to save what, $10? LOL (n/m) - BigTDogg (MA) 13:51:33 06/08/11 What $10? Don't know what you meam. (n/m) - JMartz 14:43:05 06/08/11 Versus the 300 degree kit. - BigTDogg (MA) 15:13:46 06/08/11 I would have gladly paid extra for some well made - JMartz 15:22:01 06/08/11 Glad you can take it as a lesson learned :-) (n/m) - BigTDogg (MA) 15:29:55 06/08/11 Re: The operation was a success! - ltownsgrimreaper 11:00:20 06/08/11 I used a 1/4 in. drive set with u-joints, a dremel - JMartz 13:13:40 06/08/11 Doing this right now with engine and trans still in :( - LitlElvis 12:20:39 06/08/11 People tell me theu can do this with the trans in - JMartz 13:09:16 06/08/11 All depends on your forearm size - Gennosuke 13:42:49 06/08/11 Tilting the motor (if you have the trans out) allows - JMartz 14:48:56 06/08/11 JMartz, do you have DP's installed? - LiL B 16:13:32 06/08/11 my mistake, that message was for LitlElvis (n/m) - LiL B 18:35:31 06/08/11 I've done it by cutting the tube and squeezing it flat - na300zx (OH) 13:38:22 06/08/11 That would be a system disable not a delete. (n/m) - JMartz 14:44:07 06/08/11 Not really. I am only talking about the pipe coming out - na300zx (OH) 21:15:01 06/08/11 I did it on my engine on the stand - BlackholeZ 22:35:29 06/08/11
Post a Followup	You cannot reply to this message because you are not logged in.