Subject	All depends on your forearm size
Posted by	Gennosuke on June 08, 2011 at 1:42 PM
	This message has been viewed 129 times.
In Reply To	People tell me theu can do this with the trans in posted by JMartz on June 08, 2011 at 01:09 PM
Message	if you have an ESPN bodybuilder forearm you wouldn't be able to reach down to the manifold nut. Another option where I've done the EGR delete is to just pull the lower intake plenum too (then you wont have to worry about pulling the bolts holding the EGR to the plenum due to the tight firewall). Pull the whole thing as one unit so much easier. You would of course have to address the timing belt issue though. You can clamp the timing belt, or do the EGR delete when doing a timing belt replacement.
Follow Ups	The operation was a success! - JMartz 09:34:28 06/08/11 What kit did you use? Or did you just fab something? (n/m) - new2boost 10:40:27 06/08/11 I used the Z1 kit but I would not recommend it. - JMartz 10:48:05 06/08/11 Great..I just bought that kit last week for my EGR delete.. (n/m) - new2boost 10:54:33 06/08/11 Return it and Get the 300Degree one from Kyle@IPP (n/m) - Zski 10:56:11 06/08/11 2nd. (n/m) - zfreak(Dallas) 16:37:17 06/08/11 Zero issues with the Z1 kit I've used - Gennosuke 11:42:13 06/08/11 The Z1 kit is perfectly functional. - JMartz 13:21:01 06/08/11 All that to save what, $10? LOL (n/m) - BigTDogg (MA) 13:51:33 06/08/11 What $10? Don't know what you meam. (n/m) - JMartz 14:43:05 06/08/11 Versus the 300 degree kit. - BigTDogg (MA) 15:13:46 06/08/11 I would have gladly paid extra for some well made - JMartz 15:22:01 06/08/11 Glad you can take it as a lesson learned :-) (n/m) - BigTDogg (MA) 15:29:55 06/08/11 Re: The operation was a success! - ltownsgrimreaper 11:00:20 06/08/11 I used a 1/4 in. drive set with u-joints, a dremel - JMartz 13:13:40 06/08/11 Doing this right now with engine and trans still in :( - LitlElvis 12:20:39 06/08/11 People tell me theu can do this with the trans in - JMartz 13:09:16 06/08/11 All depends on your forearm size - Gennosuke 13:42:49 06/08/11 Tilting the motor (if you have the trans out) allows - JMartz 14:48:56 06/08/11 JMartz, do you have DP's installed? - LiL B 16:13:32 06/08/11 my mistake, that message was for LitlElvis (n/m) - LiL B 18:35:31 06/08/11 I've done it by cutting the tube and squeezing it flat - na300zx (OH) 13:38:22 06/08/11 That would be a system disable not a delete. (n/m) - JMartz 14:44:07 06/08/11 Not really. I am only talking about the pipe coming out - na300zx (OH) 21:15:01 06/08/11 I did it on my engine on the stand - BlackholeZ 22:35:29 06/08/11
Post a Followup	You cannot reply to this message because you are not logged in.