Subject	fair enough however my conclusion was based on overlaying
Posted by	ztunerz on May 26, 2011 at 9:30 PM
	This message has been viewed 242 times.
In Reply To	I dis-agree.............................. posted by Greg D. (Specialty-Z) on May 26, 2011 at 12:14 PM
Message	Several dynoes that i have and in this instance te stock cam setup did very well. Obviously my sample size is a lot smaller so its not a conclusion i have fully accepted yet. Was just stating what i am seeing. I also feel that wi smaller turbos the stockers seem to do quite well vs just bolting on 500+ cams on stock heads. I guess my point was that in order to get 500+ cams to work well you need additional work. As you stated cam gear timing, as i stated headwork and bigger valves. Further, incorrect combinations of heads and lower plenums will obviously have a negative effect on timing. As you stated degreeing cams when you make a slew of changes on the engine can only help. :) Harry Formerly yellowzxtt
Follow Ups	Power Level Questions - fst300zx 21:03:25 05/25/11 A lot of power can be found in the heads (n/m) - John (MD) 21:16:49 05/25/11 Power of the mind :) (n/m) - KongZTT GT28RS MD 08:45:21 05/27/11 IMO after my latest dynoes i am convinced that - ztunerz 21:32:48 05/25/11 Is there a continuously variable cam option for our Z? - OverZealous (CT) 21:43:09 05/25/11 Even if there was , how would you control it ? (n/m) - ztunerz 23:28:37 05/25/11 with a cam controller. duh (n/m) - ZiNnYc 23:44:34 05/25/11 Buy me a standalone :),get bde to build the hardware (n/m) - ztunerz 23:50:59 05/25/11 how about I buy the standalone, and you tune it? oh wait.... (n/m) - ZiNnYc 00:01:23 05/26/11 Oh wait, what??? - OverZealous (CT) 15:42:17 05/26/11 no (n/m) - aliaZ 18:58:40 05/26/11 Bad idea? - OverZealous (CT) 23:07:29 05/26/11 good idea - aliaZ 09:23:52 05/27/11 What do you think it's worth and at what speed? - OverZealous (CT) 00:41:43 05/28/11 Re: What do you think it's worth and at what speed? - aliaZ 07:13:32 05/29/11 What about switching from the auto cams to the manual - not4resaleZ 09:27:42 05/26/11 I have tested just making that change only - Greg D. (Specialty-Z) 12:15:54 05/26/11 Adjustable sprockets before cam upgrade. - RevTech 08:52:26 05/27/11 I dis-agree.............................. - Greg D. (Specialty-Z) 12:14:15 05/26/11 With the 2560 turbo, would it be worth the effort to swap - Mr.Stacy 12:41:44 05/26/11 well............ - Greg D. (Specialty-Z) 13:00:02 05/26/11 Thanks :) A few people have told me to enjoy it, but - Mr.Stacy 13:05:27 05/26/11 Well if you still feel the bug.... - Zski 13:14:13 05/26/11 Sounds fun! I will try and make it. My son's bday is - Mr.Stacy 13:16:52 05/26/11 Starting Friday around ~4-5pm - Zski 13:20:20 05/26/11 Well said.... Makes sense. (n/m) - samsungz 12:43:18 05/26/11 have you tried the JWT solid lifter cams yet? (n/m) - JaffaUK 16:10:58 05/26/11 fair enough however my conclusion was based on overlaying - ztunerz 21:30:04 05/26/11 Area under the curve? - ZiNnYc 09:10:50 05/27/11 Re: Power Level Questions - momo2379 22:20:27 05/25/11 porting and larger valves - Greg D. (Specialty-Z) 13:08:07 05/26/11 So would it be the same concept if I didnt change the valves - fst300zx 14:59:52 05/26/11 Was in the same boat once upon a time..@ this stage in spending - samsungz 15:19:50 05/26/11 I agree, I guess I am at the point where why spend - fst300zx 15:30:05 05/26/11 Sounds like the home stretch to me :) (n/m) - samsungz 18:04:01 05/26/11 Stock Turbo w/ Breather Mods. Still Shocking! (n/m) - OverZealous (CT) 23:04:41 05/26/11
Post a Followup	You cannot reply to this message because you are not logged in.