Subject	Given your mods
Posted by	Zwin on May 23, 2011 at 2:49 PM
	This message has been viewed 184 times.
In Reply To	SZ does it again. There is no Duplicator to the Originator posted by HighPsi (NorCal) on May 23, 2011 at 11:45 AM
Message	your setup looks kind of laggy. With 2.5 piping through out the intake pipes i would expect hitting 300hp before 4k RPM and 300lbs torque before 3.5k RPM when comparing dynos posted here link.
Follow Ups	SZ does it again. There is no Duplicator to the Originator - HighPsi (NorCal) 11:45:31 05/23/11 Very nice! (n/m) - Wright (Ca) 12:01:27 05/23/11 Looks like it's slow :-) (n/m) - BigTDogg (MA) 12:40:54 05/23/11 Great numbers, mind posting a pic of your truck? - Dream Z 12:50:31 05/23/11 Excellent numbers! I see we have similar setups, but I - Mr.Stacy 13:00:48 05/23/11 Here you go>>>>>>>>>>> - Seb@Specialty-Z 13:45:17 05/23/11 Nice! In your opinion, would this angle and positioning - Mr.Stacy 15:18:40 05/23/11 Yes, I think it will help cure most of this issue. - Seb@Specialty-Z 17:47:39 05/23/11 seb in out setup with the planars and JDM nose the idle - ztunerz 20:21:42 05/23/11 yes, A-Spec (n/m) - Seb@Specialty-Z 20:29:46 05/23/11 Will the Selin translator reach both MAFs in that setup? (n/m) - Boosted1 19:00:27 05/23/11 yes, no problem. (n/m) - Seb@Specialty-Z 20:30:11 05/23/11 Given your mods - Zwin 14:49:02 05/23/11 Larger cams, shifts the curve to the right. (n/m) - HighPsi (NorCal) 15:32:07 05/23/11 hmmmm, i also have those cams - vulcanrush 15:46:03 05/23/11 I am not sure what Zwin is talking about, with these - HighPsi (NorCal) 16:15:53 05/23/11 if you look at the dynos in the link which has - Zwin 16:42:04 05/23/11 your car isn't too bad either (n/m) - vulcanrush 16:46:52 05/23/11 my 24psi pull for comparison. The cams seem to really open - Mr.Stacy 18:41:57 05/23/11 on pump gas, btw (n/m) - Mr.Stacy 05:07:20 05/24/11 larger cams usually help spool, depending on the turbo - aliaZ 21:51:14 05/23/11 agree - aliaZ 22:06:39 05/23/11 Right on point. (n/m) - John@Z1 15:08:12 05/23/11 :) (n/m) - Seb@Specialty-Z 22:00:50 05/23/11 Impressive peak number on those GT600's... Without the full - samsungz 17:23:31 05/23/11 Sweet results anyway you can e-mail me the win pep files - ztunerz 20:19:52 05/23/11 I'd be interested in seeing that... - Jim (Selin Design) 01:08:50 05/24/11 Well no win pep file yet but i did a little analysis anyway - ztunerz 18:20:38 05/24/11 What is a win pep file? (n/m) - HighPsi (NorCal) 20:27:52 05/24/11 Its a file the dynojet creates I can as Seb for it (n/m) - ztunerz 23:36:30 05/25/11 Jealous -----> (n/m) - KevinsFairlady 00:59:27 05/24/11
Post a Followup	You cannot reply to this message because you are not logged in.