Subject	pistons
Posted by	dzero196 on May 09, 2011 at 2:40 PM
	This message has been viewed 160 times.
In Reply To	Oh JEEZ... posted by eriksu9 on May 09, 2011 at 02:20 PM
Message	since i have to replace the pistons and get my block honed how would i be better off getting my block bored for .040 88mm pistons?
Follow Ups	my accomplishments for mothers day weekend haha sorry mom - dzero196 11:50:23 05/09/11 Nice work. Tstat bleeder should be on top. - PiotrC70 11:58:22 05/09/11 Thermostat pic is blurry..is there a flow through at - BoneZ 11:58:33 05/09/11 I STORNGLY advise against the use of that thermostat - Bernie (NoVA) 12:00:39 05/09/11 2nd.. - KongZTT GT28RS MD 12:03:56 05/09/11 Re: 2nd.. - dzero196 12:05:45 05/09/11 Better now then after the motor pops. (n/m) - Bernie (NoVA) 12:08:11 05/09/11 Re: Better now then after the motor pops. - dzero196 12:19:21 05/09/11 Luckily you caught the piston orientation sooner than later! - KongZTT GT28RS MD 12:01:12 05/09/11 Re: Luckily you caught the piston orientation sooner than later! - dzero196 12:07:17 05/09/11 Hi :) (n/m) - Woody75 (Denver) 12:41:07 05/09/11 Thank god for the woody's! - KongZTT GT28RS MD 14:55:02 05/09/11 Score yet another save for Woody, so many I've lost count! (n/m) - Cuis-Z 20:27:00 05/09/11 Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:02:09 05/09/11 Re: Re: my accomplishments for mothers day weekend haha sorry mom - dzero196 12:11:20 05/09/11 Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:13:26 05/09/11 Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - dzero196 12:18:44 05/09/11 oops - aliaZ 12:21:58 05/09/11 Re: oops - dzero196 12:30:09 05/09/11 Re: Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:26:01 05/09/11 Re: Re: Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - dzero196 13:07:20 05/09/11 This is an example of a thread someone would pull up - TriniTT 13:47:55 05/09/11 Que? Please elaborate further. (n/m) - Summeronthechain (MN) 12:44:49 05/09/11 Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:15:38 05/09/11 ...wow.... (n/m) - zfreak(Dallas) 14:08:27 05/09/11 2nd. (n/m) - Stadsport (PHX) 15:28:38 05/09/11 Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 14:17:22 05/09/11 Oh JEEZ... - eriksu9 14:20:06 05/09/11 pistons - dzero196 14:40:09 05/09/11 87.5mm is the largest I'd go (personally) - KongZTT GT28RS MD 14:56:29 05/09/11 stupid question.. - NissanZ300 16:17:55 05/09/11 Unbolt connecting rod from crank, slide piston/rod assembly - Dave N 16:25:04 05/09/11 lmfao - NissanZ300 16:29:22 05/09/11 Re: lmfao - Dave N 17:11:09 05/09/11 piston pin is offset - aliaZ 16:32:05 05/09/11 im sorry - NissanZ300 16:38:45 05/09/11 oops...no worries (n/m) - aliaZ 16:58:15 05/09/11 Re: oops...no worries - dzero196 20:24:16 05/09/11
Post a Followup	You cannot reply to this message because you are not logged in.