Subject	Re: Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom
Posted by	CmyZ on May 09, 2011 at 12:26 PM
	This message has been viewed 206 times.
In Reply To	Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom posted by dzero196 on May 09, 2011 at 12:18 PM
Message	That is a no no, you needed to get the block honed, you will have poor compression and leakage problems. The rings will not seat as aliaZ indicated. I would have it honed and check the piston wall clearance at the same time. If not all that hard work you have put so far, will go to waste.
Follow Ups	my accomplishments for mothers day weekend haha sorry mom - dzero196 11:50:23 05/09/11 Nice work. Tstat bleeder should be on top. - PiotrC70 11:58:22 05/09/11 Thermostat pic is blurry..is there a flow through at - BoneZ 11:58:33 05/09/11 I STORNGLY advise against the use of that thermostat - Bernie (NoVA) 12:00:39 05/09/11 2nd.. - KongZTT GT28RS MD 12:03:56 05/09/11 Re: 2nd.. - dzero196 12:05:45 05/09/11 Better now then after the motor pops. (n/m) - Bernie (NoVA) 12:08:11 05/09/11 Re: Better now then after the motor pops. - dzero196 12:19:21 05/09/11 Luckily you caught the piston orientation sooner than later! - KongZTT GT28RS MD 12:01:12 05/09/11 Re: Luckily you caught the piston orientation sooner than later! - dzero196 12:07:17 05/09/11 Hi :) (n/m) - Woody75 (Denver) 12:41:07 05/09/11 Thank god for the woody's! - KongZTT GT28RS MD 14:55:02 05/09/11 Score yet another save for Woody, so many I've lost count! (n/m) - Cuis-Z 20:27:00 05/09/11 Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:02:09 05/09/11 Re: Re: my accomplishments for mothers day weekend haha sorry mom - dzero196 12:11:20 05/09/11 Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:13:26 05/09/11 Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - dzero196 12:18:44 05/09/11 oops - aliaZ 12:21:58 05/09/11 Re: oops - dzero196 12:30:09 05/09/11 Re: Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:26:01 05/09/11 Re: Re: Re: Re: Re: Re: my accomplishments for mothers day weekend haha sorry mom - dzero196 13:07:20 05/09/11 This is an example of a thread someone would pull up - TriniTT 13:47:55 05/09/11 Que? Please elaborate further. (n/m) - Summeronthechain (MN) 12:44:49 05/09/11 Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 12:15:38 05/09/11 ...wow.... (n/m) - zfreak(Dallas) 14:08:27 05/09/11 2nd. (n/m) - Stadsport (PHX) 15:28:38 05/09/11 Re: my accomplishments for mothers day weekend haha sorry mom - CmyZ 14:17:22 05/09/11 Oh JEEZ... - eriksu9 14:20:06 05/09/11 pistons - dzero196 14:40:09 05/09/11 87.5mm is the largest I'd go (personally) - KongZTT GT28RS MD 14:56:29 05/09/11 stupid question.. - NissanZ300 16:17:55 05/09/11 Unbolt connecting rod from crank, slide piston/rod assembly - Dave N 16:25:04 05/09/11 lmfao - NissanZ300 16:29:22 05/09/11 Re: lmfao - Dave N 17:11:09 05/09/11 piston pin is offset - aliaZ 16:32:05 05/09/11 im sorry - NissanZ300 16:38:45 05/09/11 oops...no worries (n/m) - aliaZ 16:58:15 05/09/11 Re: oops...no worries - dzero196 20:24:16 05/09/11
Post a Followup	You cannot reply to this message because you are not logged in.