Subject	HPC quoted some seriously bold claims in underhood temp and
Posted by	LJZTT on April 16, 2011 at 6:05 AM
	This message has been viewed 287 times.
In Reply To	I think this is what is commonly referred to as posted by Ash's Z on April 16, 2011 at 03:32 AM
Message	surface temp reductions, though their US site has changed since then and I dont see it anymore. Was 90% of the reason I got mine done. "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." --Winston Churchill END THE FED ....learn why, in 42 minutes Full Pardon for PFC Bradley Manning
Follow Ups	Thinking about getting my new MS manifolds ceramic coated.. - ForceFedTT (SoCal) 00:00:48 04/16/11 When I talked to Mike Smith about swain coating them.. - KongZTT GT28RS MD 00:31:48 04/16/11 I have coated every manifold and turbine housing on - ztunerz 03:13:27 04/16/11 Why would you choose a rusty finish? - JMartz 07:57:52 04/16/11 How about using hi-temp exhaust paint? - ZXoltan 08:27:42 04/16/11 Burns right off - dogpile 08:36:41 04/16/11 i didn't do it for the finish per se, i did it for the temps (n/m) - ztunerz 18:04:02 04/16/11 I think this is what is commonly referred to as - Ash's Z 03:32:01 04/16/11 HPC quoted some seriously bold claims in underhood temp and - LJZTT 06:05:07 04/16/11 HPC did mine for me as is (n/m) - LJZTT 06:03:27 04/16/11 I have coated and non coated. - Boosted1 09:00:27 04/16/11 400 f surface temp diff after a pull on the dyno is not - ztunerz 10:47:37 04/16/11 I just split some very expensive hairs lmao (n/m) - ZiNnYc 12:09:33 04/16/11 Harry, where do you get your coatings done? - ZXoltan 12:52:38 04/16/11 Local guy in Tampa bay, measuring at the collector (n/m) - ztunerz 18:00:11 04/16/11 Is this Swain coating or ceramic coating (jet hot) etc? (n/m) - KongZTT GT28RS MD 15:14:23 04/17/11 Not sure. They were already coated when I purchased. - Boosted1 16:00:42 04/17/11 Jet hot looks like a "chrome" powdercoat almost.. - KongZTT GT28RS MD 16:05:24 04/17/11 Install part and enjoy..... - The Hawk 09:05:46 04/16/11 Ceramic coated my Mike Smith Manifolds in June 2008,installed - samsungz 12:51:42 04/16/11 there you go, a second data point (n/m) - ztunerz 18:01:16 04/16/11 What about a wrap, or coating and wrap? (n/m) - BoneZ 14:25:50 04/16/11 The only thing I didn't like about wraps.. - KongZTT GT28RS MD 15:17:30 04/17/11 Good info. I had my manis coated by Swain, but looking - BoneZ 17:40:17 04/17/11 Cool. I'm gonna go ahead and get the manis and turbine housings - ForceFedTT (SoCal) 18:18:15 04/16/11
Post a Followup	You cannot reply to this message because you are not logged in.