Subject	IC pipes will be 2.5" OD and run along frame rail >>
Posted by	LitlElvis on March 04, 2011 at 4:54 PM
	This message has been viewed 100 times.
In Reply To	Did you leave any room for the ic piping? :) posted by Wright (Ca) on March 04, 2011 at 02:03 PM
Message	VTC covers allow using a spanner wrench to rotate the cams a bit to set their timing.
Follow Ups	Mike Smith INLET piping diameters (Inducer and inlet ends) - KongZTT GT28RS MD 11:42:52 03/04/11 Very nice! - Bigwill837 11:46:58 03/04/11 He will offer them with a 2-bolt flange.. - KongZTT GT28RS MD 12:03:02 03/04/11 Did you check with Mike before posting specs? - BigTDogg (MA) 12:04:28 03/04/11 No I didn't.. but I dont think it would really matter.. - KongZTT GT28RS MD 12:11:50 03/04/11 And also.. FWIW - KongZTT GT28RS MD 12:14:22 03/04/11 Cool, just checking. - BigTDogg (MA) 12:17:02 03/04/11 LOL - KongZTT GT28RS MD 12:21:20 03/04/11 typo.. the pass side inlet (induction connection) is ~58.5mm - KongZTT GT28RS MD 12:55:16 03/04/11 The reason I asked - sparkie 13:16:24 03/04/11 measure the O.D of your stock induction pipes (accordian) - KongZTT GT28RS MD 13:22:46 03/04/11 I'm not using the stock accordian pipe. (n/m) - sparkie 15:02:44 03/04/11 My point was.. its close to 3" O.D.. - KongZTT GT28RS MD 15:23:09 03/04/11 Thread Hi-jack... 4" OD turbo inlet pipes of death :) - LitlElvis 13:57:08 03/04/11 Did you leave any room for the ic piping? :) - Wright (Ca) 14:03:40 03/04/11 IC pipes will be 2.5" OD and run along frame rail >> - LitlElvis 16:54:29 03/04/11 Oh, very cool. Do you sell these covers and spanner wrench? (n/m) - Wright (Ca) 17:21:48 03/04/11 Purdy...Pipes of Death sound scary though! lol - BoneZ 14:03:43 03/04/11 like (n/m) - Jim (Selin Design) 14:12:41 03/04/11 holy mother - KongZTT GT28RS MD 14:13:42 03/04/11 what FPR is that? (n/m) - aliaZ 14:56:05 03/04/11 MagnaFuel 9950b. - ZiNnYc 15:45:58 03/04/11 It's the MagnaFuel FPR of Death... rated at 2000HP :) - LitlElvis 16:56:04 03/04/11 yes I did, thanks (n/m) - aliaZ 17:10:52 03/04/11 That is insane!!! - RobZ32 16:01:55 03/04/11 ETA? Never, at my pace. ICs are planned and there is room - LitlElvis 17:02:07 03/04/11 There was a member a while back that did 2.5" piping - KongZTT GT28RS MD 17:08:12 03/04/11 John abeler did that. Cleans up the engine bay nicely (n/m) - ztunerz 18:04:14 03/04/11 I wonder where he's been? (n/m) - KongZTT GT28RS MD 18:55:59 03/04/11 I talk to him a couple times a week to argue politics :) (n/m) - ztunerz 08:39:10 03/06/11 He used to call me once in a while to just talk Z's.. - KongZTT GT28RS MD 14:01:54 03/06/11 Makes we want to build a race car :) (n/m) - ztunerz 18:02:41 03/04/11 another one? :) (n/m) - KongZTT GT28RS MD 18:55:26 03/04/11 Very nice. Thanks for posting. (n/m) - Boosted1 18:23:35 03/04/11 That's right in the neighborhood of what I expected to see. - Ash's Z 03:07:37 03/05/11 No problem.. Looking forward to seeing what u come up with! (n/m) - KongZTT GT28RS MD 03:17:44 03/05/11
Post a Followup	You cannot reply to this message because you are not logged in.