Subject	Thread Hi-jack... 4" OD turbo inlet pipes of death :)
Posted by	LitlElvis on March 04, 2011 at 1:57 PM
	This message has been viewed 939 times.
In Reply To	Mike Smith INLET piping diameters (Inducer and inlet ends) posted by KongZTT GT28RS MD on March 04, 2011 at 11:42 AM
Message	I figure I can pick up some spare cash by vacuuming parking lots with these babies. Ok, I'm done... nice stuff there Shawn. MSP does good things.
Follow Ups	Mike Smith INLET piping diameters (Inducer and inlet ends) - KongZTT GT28RS MD 11:42:52 03/04/11 Very nice! - Bigwill837 11:46:58 03/04/11 He will offer them with a 2-bolt flange.. - KongZTT GT28RS MD 12:03:02 03/04/11 Did you check with Mike before posting specs? - BigTDogg (MA) 12:04:28 03/04/11 No I didn't.. but I dont think it would really matter.. - KongZTT GT28RS MD 12:11:50 03/04/11 And also.. FWIW - KongZTT GT28RS MD 12:14:22 03/04/11 Cool, just checking. - BigTDogg (MA) 12:17:02 03/04/11 LOL - KongZTT GT28RS MD 12:21:20 03/04/11 typo.. the pass side inlet (induction connection) is ~58.5mm - KongZTT GT28RS MD 12:55:16 03/04/11 The reason I asked - sparkie 13:16:24 03/04/11 measure the O.D of your stock induction pipes (accordian) - KongZTT GT28RS MD 13:22:46 03/04/11 I'm not using the stock accordian pipe. (n/m) - sparkie 15:02:44 03/04/11 My point was.. its close to 3" O.D.. - KongZTT GT28RS MD 15:23:09 03/04/11 Thread Hi-jack... 4" OD turbo inlet pipes of death :) - LitlElvis 13:57:08 03/04/11 Did you leave any room for the ic piping? :) - Wright (Ca) 14:03:40 03/04/11 IC pipes will be 2.5" OD and run along frame rail >> - LitlElvis 16:54:29 03/04/11 Oh, very cool. Do you sell these covers and spanner wrench? (n/m) - Wright (Ca) 17:21:48 03/04/11 Purdy...Pipes of Death sound scary though! lol - BoneZ 14:03:43 03/04/11 like (n/m) - Jim (Selin Design) 14:12:41 03/04/11 holy mother - KongZTT GT28RS MD 14:13:42 03/04/11 what FPR is that? (n/m) - aliaZ 14:56:05 03/04/11 MagnaFuel 9950b. - ZiNnYc 15:45:58 03/04/11 It's the MagnaFuel FPR of Death... rated at 2000HP :) - LitlElvis 16:56:04 03/04/11 yes I did, thanks (n/m) - aliaZ 17:10:52 03/04/11 That is insane!!! - RobZ32 16:01:55 03/04/11 ETA? Never, at my pace. ICs are planned and there is room - LitlElvis 17:02:07 03/04/11 There was a member a while back that did 2.5" piping - KongZTT GT28RS MD 17:08:12 03/04/11 John abeler did that. Cleans up the engine bay nicely (n/m) - ztunerz 18:04:14 03/04/11 I wonder where he's been? (n/m) - KongZTT GT28RS MD 18:55:59 03/04/11 I talk to him a couple times a week to argue politics :) (n/m) - ztunerz 08:39:10 03/06/11 He used to call me once in a while to just talk Z's.. - KongZTT GT28RS MD 14:01:54 03/06/11 Makes we want to build a race car :) (n/m) - ztunerz 18:02:41 03/04/11 another one? :) (n/m) - KongZTT GT28RS MD 18:55:26 03/04/11 Very nice. Thanks for posting. (n/m) - Boosted1 18:23:35 03/04/11 That's right in the neighborhood of what I expected to see. - Ash's Z 03:07:37 03/05/11 No problem.. Looking forward to seeing what u come up with! (n/m) - KongZTT GT28RS MD 03:17:44 03/05/11
Post a Followup	You cannot reply to this message because you are not logged in.