Subject	Re: Flowtest Results for Turbo Inlet System >>>>
Posted by	ba11erz on March 01, 2011 at 8:02 PM
	This message has been viewed 299 times.
In Reply To	Flowtest Results for Turbo Inlet System >>>> posted by Ash's Z on March 01, 2011 at 01:07 PM
Message	Ash, the time and effort you've taken to capture this data is noteworthy. Job well done on your laborious research! Would it be more of a challenge to build a mock test environment where the length of the piping is measured and compared? (strait vs mandrel bends) I have a suspicion if that data is captured and compiled, it may tell us the bends and turns of the entire flow system are either minimal or extreme, rather more laminar or turbulent. Your thoughts? Silas
Follow Ups	Flowtest Results for Turbo Inlet System >>>> - Ash's Z 13:07:55 03/01/11 Great work Ash, but more importantly - s3trios 13:18:29 03/01/11 that's getting old (n/m) - ali300zx 13:20:42 03/01/11 Not really, you watch... It'll happen unfortunately (n/m) - BigTDogg (MA) 13:25:31 03/01/11 right... that's why mentioning AMS everytime a new - ali300zx 15:36:40 03/01/11 It's still worthwhile mentioning for Noobs and inexperienced - Zarcasm(Hfd, CT) 20:34:05 03/01/11 Ash, you lil devil--you did it again :) (n/m) - ForceFedTT (SoCal) 13:21:18 03/01/11 Thoughts on using the Z1 replacement accordian pipes - EricTTZ 13:22:25 03/01/11 I dont forsee any fitment issues using those, but I still - Ash's Z 13:25:25 03/01/11 Adequate? So are you thinking bigger piping could net more - 5280Z_nightstalker 13:39:19 03/01/11 Dont confuse the turbo inlet side to the pressurized pipes. - Ash's Z 13:55:46 03/01/11 what would the effect be of increased air flow and volume - The Devils Z 18:11:45 03/01/11 Well, when speaking of VE, the focus is on how well the - Ash's Z 09:26:39 03/02/11 I didn't read 1/2 your response --sorry --I think I phrased - The Devils Z 12:57:29 03/02/11 Yes, allowing the turbo to breathe air more easily into its - Ash's Z 08:34:01 03/03/11 yep ...thanks (n/m) - The Devils Z 05:25:01 03/04/11 Awesome results Ash! (n/m) - Z32TT-R 13:51:46 03/01/11 Thanks for your research in this area. I'm certain you will - not4resaleZ 14:06:28 03/01/11 Great data! Pretty awesome. (n/m) - The Hawk 14:24:11 03/01/11 Any idea as to an ETA on these pipes? - arkansasturbo 15:08:56 03/01/11 If you keep enlarging pipes on the intake side - Shiers69 15:18:03 03/01/11 3", not really a problem with dual MAFs. (n/m) - CoHPhasor 17:47:15 03/01/11 2 questions: - blackomega 15:27:41 03/01/11 1) band-aid fix 2)somewhere between bloody and impossible (n/m) - zgene4 15:49:25 03/01/11 so what would be the real fix? - blackomega 16:12:46 03/01/11 straight inlet pipes... (n/m) - BigTDogg (MA) 16:23:38 03/01/11 real short, fat ones. (n/m) - Zarcasm(Hfd, CT) 20:41:25 03/01/11 i would think bde motor/engine mounts would be a good idea (n/m) - vulcanrush 15:59:46 03/01/11 Awesome. Thanks for posting! (n/m) - Madhatter10-6 15:48:52 03/01/11 Ash , Im days away from dropping my motor in but - xteam300tt 18:47:31 03/01/11 nice data....3" accordian pipe..?... - zdoc 18:48:21 03/01/11 Re: Flowtest Results for Turbo Inlet System >>>> - Hoov100 19:03:20 03/01/11 The biggest restriction will likely always be in a - not4resaleZ 19:18:49 03/01/11 Re: Flowtest Results for Turbo Inlet System >>>> - ba11erz 20:02:03 03/01/11 Good job! (n/m) - TheTwinZ (Peru) 21:22:31 03/01/11 Did you get my emails with pictures? - Atl300zxTT 10:33:53 03/02/11
Post a Followup	You cannot reply to this message because you are not logged in.