Subject	so basically what you both are saying is that the gains
Posted by	The Devils Z on February 20, 2011 at 2:35 PM
	This message has been viewed 183 times.
In Reply To	2nd^^ posted by LitlElvis on February 20, 2011 at 12:26 PM
Message	from Ash's design negate the question of the opening header size (That's assuming that I understand what you both are saying correctly) ..if the designs were the same - would the large opening be better ? To use Ztuner's comment -- a bigger opening provides a lip against reversion .. =============Sig begins here================ The Devils Z.com The Devils Z Pic 666 rwhp dyno View Me! Disclaimer : Not Safe For Work !
Follow Ups	AshsZ-II Ultimate Street Z - Manifold Flowtest >>>> - Ash's Z 12:49:59 02/19/11 Very interesting. (n/m) - Summeronthechain (MN) 13:45:12 02/19/11 Awesome (n/m) - toykoz32 13:58:38 02/19/11 Looks good but I'll stick with AMS. Flow data says it all. - PiotrC70 14:41:44 02/19/11 LMAO (n/m) - ZiNnYc 14:47:06 02/19/11 additional holes in the casting for extra air flow! (n/m) - Shiers69 15:05:58 02/19/11 LOL (n/m) - zfreak(Dallas) 15:54:29 02/19/11 You forgot to say they're much cheaper too LOL (n/m) - SWhiteTT(WA) 16:40:36 02/19/11 Thats awsome! (n/m) - MeatMan - 604Z.ca - 19:07:05 02/19/11 So its possible youd be breaking 700 with the MS... (n/m) - ZiNnYc 14:46:47 02/19/11 Based on the results, would you eventually swap yours for - PiotrC70 14:47:52 02/19/11 I think Ash would pull his motor for any reason...hehe (n/m) - dpjax 15:25:26 02/19/11 Most likely will be the final decision at some point to go - Ash's Z 16:22:50 02/19/11 Ash, I love when you make posts... - akdawgg99 21:51:56 02/19/11 get a room ;) (n/m) - ForceFedTT (SoCal) 04:59:53 02/21/11 Question about your comment : - The Devils Z 06:45:47 02/20/11 Whats important for an exhaust manifold is - ztunerz 10:55:37 02/20/11 2nd^^ - LitlElvis 12:26:41 02/20/11 Agreed (n/m) - ztunerz 12:32:52 02/20/11 so basically what you both are saying is that the gains - The Devils Z 14:35:49 02/20/11 no, I didn't say that a smaller opening would be better. - Ash's Z 08:53:34 02/21/11 thank you for the clarity (n/m) - The Devils Z 15:25:10 02/21/11 In what flow direction did you test the manifolds? - LitlElvis 12:05:25 02/20/11 2nd - entry radius is important if you're sucking air in (n/m) - Zarcasm(Hfd, CT) 15:48:05 02/20/11 693RWHP on racefuel at 30.5psi? Average joe does not boost - RevTech 15:47:56 02/20/11 Perhaps not, but the power at 18psi is what it is, and its - Ash's Z 08:55:05 02/21/11 Keep up the good work, Ash. (n/m) - Milo (SATX) 20:48:23 02/20/11
Post a Followup	You cannot reply to this message because you are not logged in.