Subject	Most likely will be the final decision at some point to go
Posted by	Ash's Z on February 19, 2011 at 4:22 PM
	This message has been viewed 430 times.
In Reply To	Based on the results, would you eventually swap yours for posted by PiotrC70 on February 19, 2011 at 02:47 PM
Message	to the MS manifolds. The reliability of cast iron in addition to the improved flow is an easy decision. Only caveat is that my turbo placement is slightly different than stock which means I'll have to do some modification to my downpipes. Swapping in a set of Greg's expansion DPs wont work either as the 3-bolt flange at the end of the downpipes I made is also in a slightly different location than OE. No big deal to do though. A few hours of fabbing and that's taken care of. Perhaps in another 15K or 30K or more I'll swap out to MS. My manifolds are holding up really well and Im a bit fond of them. :) Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	AshsZ-II Ultimate Street Z - Manifold Flowtest >>>> - Ash's Z 12:49:59 02/19/11 Very interesting. (n/m) - Summeronthechain (MN) 13:45:12 02/19/11 Awesome (n/m) - toykoz32 13:58:38 02/19/11 Looks good but I'll stick with AMS. Flow data says it all. - PiotrC70 14:41:44 02/19/11 LMAO (n/m) - ZiNnYc 14:47:06 02/19/11 additional holes in the casting for extra air flow! (n/m) - Shiers69 15:05:58 02/19/11 LOL (n/m) - zfreak(Dallas) 15:54:29 02/19/11 You forgot to say they're much cheaper too LOL (n/m) - SWhiteTT(WA) 16:40:36 02/19/11 Thats awsome! (n/m) - MeatMan - 604Z.ca - 19:07:05 02/19/11 So its possible youd be breaking 700 with the MS... (n/m) - ZiNnYc 14:46:47 02/19/11 Based on the results, would you eventually swap yours for - PiotrC70 14:47:52 02/19/11 I think Ash would pull his motor for any reason...hehe (n/m) - dpjax 15:25:26 02/19/11 Most likely will be the final decision at some point to go - Ash's Z 16:22:50 02/19/11 Ash, I love when you make posts... - akdawgg99 21:51:56 02/19/11 get a room ;) (n/m) - ForceFedTT (SoCal) 04:59:53 02/21/11 Question about your comment : - The Devils Z 06:45:47 02/20/11 Whats important for an exhaust manifold is - ztunerz 10:55:37 02/20/11 2nd^^ - LitlElvis 12:26:41 02/20/11 Agreed (n/m) - ztunerz 12:32:52 02/20/11 so basically what you both are saying is that the gains - The Devils Z 14:35:49 02/20/11 no, I didn't say that a smaller opening would be better. - Ash's Z 08:53:34 02/21/11 thank you for the clarity (n/m) - The Devils Z 15:25:10 02/21/11 In what flow direction did you test the manifolds? - LitlElvis 12:05:25 02/20/11 2nd - entry radius is important if you're sucking air in (n/m) - Zarcasm(Hfd, CT) 15:48:05 02/20/11 693RWHP on racefuel at 30.5psi? Average joe does not boost - RevTech 15:47:56 02/20/11 Perhaps not, but the power at 18psi is what it is, and its - Ash's Z 08:55:05 02/21/11 Keep up the good work, Ash. (n/m) - Milo (SATX) 20:48:23 02/20/11
Post a Followup	You cannot reply to this message because you are not logged in.