Subject	directly through both the 15* mark and the crank pulley
Posted by	LJZTT on December 31, 2010 at 11:46 AM
	This message has been viewed 75 times.
In Reply To	What is the correct viewing angle? (n/m) posted by Wright (Ca) on December 31, 2010 at 11:25 AM
Message	center, assuming you are setting to 15 degrees I forgot to mark my timing belt cover for future timing tweaks. "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." --Winston Churchill END THE FED ....learn why, in 42 minutes Full Pardon for PFC Bradley Manning
Follow Ups	Getting there, Maybe next year.......... - whip 09:25:33 12/31/10 I say you just put it in your living room on display - BigTDogg (MA) 09:45:27 12/31/10 It was the driver side turbo, just going - whip 13:55:13 12/31/10 Just get a used turbo housing and swap it over. (n/m) - Woody75 (Denver) 10:00:44 12/31/10 Agreed - or have a machine shop take it out for you. (n/m) - Bernie (NoVA) 10:33:56 12/31/10 I attempted to switch out the housing for another, - whip 13:47:01 12/31/10 used turbos ::thumbs down:: - ZiNnYc 10:44:32 12/31/10 dunno if you thought of this already, but something I wished - LJZTT 10:48:55 12/31/10 What is the correct viewing angle? (n/m) - Wright (Ca) 11:25:31 12/31/10 Merry Christmas!! - BigTDogg (MA) 11:46:32 12/31/10 How very nice of you :) - Wright (Ca) 12:33:42 12/31/10 directly through both the 15* mark and the crank pulley - LJZTT 11:46:54 12/31/10 Wow! Very nice! - ZXoltan 11:29:56 12/31/10 Had the timing covers professionally painted. - whip 13:39:02 12/31/10 love it! looks amazing (n/m) - John90zxtt(OH) 11:30:07 12/31/10 Very nice, I appreciate the attention to detail! (n/m) - 91Z32TT 11:51:38 12/31/10 Very nice. It will all pay off when it starts up for the - PiotrC70 12:04:14 12/31/10 depending how deep the stud/bolt broke off... - KongZTT GT28RS MD 12:46:04 12/31/10 Sure is pretty!! (n/m) - Boris 13:16:23 12/31/10 That's too beautiful to get dirty - njz 13:58:52 12/31/10 Looking good. (n/m) - Ghoztt (CO) 15:17:27 12/31/10 nice. Even new hardware! (n/m) - zfreak(Dallas) 15:19:46 12/31/10 Great looking engine. Very NICE! (n/m) - Ziceman(East TN) 15:21:45 12/31/10 AWESOME!!! Definetly A show Stopper. Great Job! (n/m) - scott@RDZ 16:22:24 12/31/10 Looks amazing! (n/m) - Wright (Ca) 17:12:28 12/31/10 Super Clean... :0) (n/m) - Turnerscasa (Dallas) 19:12:10 12/31/10 Keep up the good work. Coming along. (n/m) - Milo (SATX) 04:23:11 01/01/11 Drool. Thumbs up on the whole job, esp the plenum. (n/m) - cherryz 11:04:04 01/01/11 looks better then new!!! (n/m) - 96toplessZ 16:04:00 01/01/11
Post a Followup	You cannot reply to this message because you are not logged in.