Subject	route the PTU wiring under the intake soft hoses
Posted by	vorpalZ on December 18, 2010 at 8:41 AM
	This message has been viewed 173 times.
In Reply To	thanks posted by KasbeKZ(VA) on December 18, 2010 at 12:53 AM
Message	and feed it between the rad & support into the front intake area. You won't have much extra once you connect up the PTU in the front. The split from the main harness is roughly under the intake hoses. Any extra wiring I pull into the front intake area & zip tie under the PTU. Regards, WARNING!  Forum posts are likely to contain traces of irony. If you believe you may be suffering from an irony deficiency please consult your physician. My Zs are hybrid vehicles, they run on gasoline and money I'm off to wax mine and go for a drive now. - BigTDogg (MA) 07:17:08 07/17/09 times change, people change, but the Z32 still kicks ass. - apudapus 16:46:02 06/15/07 I was more wondering how you set your climate control to 22* lol, it would be that fastest freezer on wheels! - Briscoe'sZ32 (NJ) 23:15:44 02/05/07 You have *got* to be getting a cut from B&B :D - SeedyROM 15:24:29 08/16/06 What do you think B&B stands for? - YugoBernie (NoVA) 15:57:09 08/16/06
Follow Ups	can't find any PTU relocation pictures - KasbeKZ(VA) 21:27:49 12/17/10 . - ZiNnYc 21:39:28 12/17/10 thanks. i'm surprised i didn't see that in my search (n/m) - KasbeKZ(VA) 22:22:05 12/17/10 yes - vorpalZ 22:07:36 12/17/10 IIRC, you remove the upper brace for the rad - CoHPhasor 22:40:24 12/17/10 correct... fourth pic (n/m) - vorpalZ 22:51:03 12/17/10 Ditto. - scoTTinald (BC) 23:01:21 12/17/10 thanks - KasbeKZ(VA) 00:53:24 12/18/10 route the PTU wiring under the intake soft hoses - vorpalZ 08:41:56 12/18/10 Yup. That's where mine was at. - zfreak(Dallas) 10:48:00 12/18/10 Under nose panel. - jschrauwen 06:10:16 12/18/10 Good idea. Doesn't mess up the view... - 240Z FeO2 12:25:39 12/18/10 Not a great pic, but where mine lives... - Stadsport (PHX) 15:48:13 12/18/10 i like that place. how did you attach it? - KasbeKZ(VA) 16:08:57 12/18/10 I used one of the bolt holes for the relay box iirc - Stadsport (PHX) 16:12:52 12/18/10 FYI - Bernie (NoVA) 16:22:50 12/18/10 Re: FYI - Stadsport (PHX) 19:08:59 12/18/10 Carry on. (n/m) - Bernie (NoVA) 11:38:46 12/19/10 Mine too, easier to get timing readings (n/m) - BigTDogg (MA) 09:35:11 12/19/10 Doe this count? - intel 18:12:25 12/18/10 Bad place for the transistor pack - Spddracer 18:21:54 12/18/10 Eh will have to see I guess. - intel 19:49:45 12/18/10 eh I dunno - aliaZ 08:47:21 12/19/10 The old ones did have fins, but they also failed - BigTDogg (MA) 09:36:11 12/19/10 You can fix the old ones, Simple cold solder joint. (n/m) - Spddracer 14:01:11 12/19/10 Yep - ArubaDave 14:09:20 12/19/10 not just in the engine bay, but in the hottest part - vorpalZ 10:07:21 12/19/10 Very cool! Do you have a copy of this picture with - Jim (Selin Design) 12:10:24 12/20/10 Sorry, no - vorpalZ 12:36:48 12/20/10
Post a Followup	You cannot reply to this message because you are not logged in.