Subject	Interesting since in empirial testing i found
Posted by	ztunerz on December 10, 2010 at 8:18 PM
	This message has been viewed 146 times.
In Reply To	Greddys only flow a bit more than stock. posted by The Hawk on December 10, 2010 at 12:41 PM
Message	The greddys to control temps much better than stock and even better than stillens. I also had greddy on a car that made close to 700 whp with gt28rs turbos with stock sized valves, 400+ cams, stock size piping. Never seen stillens or z1 ics or any smics other than ash spec massives do that. Flow is only one aspect of ic's . Look inside the core of a greddy ic and it will all make sense. It has this tiny spikes that stick into the core that slow down the speed of air flowing thru allowing tye cair to cool far better than the typical bar and plate setup. Also look at the tubes in the core ther are round not square so even though the core is 4 inch thick air slows thru without much resistance. Size is not everything, sometimes the design matters too :) Harry Formerly yellowzxtt
Follow Ups	Im going to be upgrading to Ashspec Massives - Nis300owner 00:30:26 12/10/10 I believe SZ can modify the stillens to 2.5 in and out maybe - 5280Z_nightstalker 00:38:31 12/10/10 they can but they wont be as thick as the massives - Nis300owner 00:44:16 12/10/10 Just throwing it out their as a cheaper alternative. - 5280Z_nightstalker 00:54:31 12/10/10 Waves magic wand..... - SeanK (StL) 01:29:20 12/10/10 damn (n/m) - blackomega 01:37:16 12/10/10 I knew that graph was around but I didnt notice they did - 5280Z_nightstalker 01:41:21 12/10/10 I'll do you one better. - ZiNnYc 03:43:24 12/10/10 Good link. (n/m) - SimaYi 11:03:59 12/10/10 bookmarked, great info. (n/m) - fantomZ(OH) 13:55:41 12/10/10 Most helpful post from you in over a year... - ni[X]it 16:41:05 12/10/10 kma (n/m) - ZiNnYc 18:45:53 12/10/10 2nd (ni[x]it) (n/m) - CoHPhasor 19:23:39 12/10/10 there is a flaw in that thread regarding crossflow theory - aliaZ 16:54:17 12/10/10 Are the AshSPEC Sport SMICs *essentially* the same - BigTDogg (MA) 07:42:50 12/10/10 IIRC, they were the same until Ash left Z1. Now I think Ash - PiotrC70 08:31:34 12/10/10 Same cores, both cast aluminum endtanks with what look to be - ZiNnYc 08:35:43 12/10/10 Same core, different endtanks. We cast our endtanks but - Ash's Z 11:12:53 12/10/10 I'll post a pic of mine when I get home. I got them used - BigTDogg (MA) 11:22:09 12/10/10 You'll need to mesure the i.d. of the inlet/outlet ports - Ash's Z 12:00:23 12/10/10 I'd like to see what you could do with your 2.5" piping - not4resaleZ 21:23:57 12/10/10 i would definately consider modifying my GReddys because - blackomega 01:28:07 12/10/10 TIG welder, some practice and proper technique and ur good (n/m) - Ted(Snowflake..) 04:33:33 12/10/10 Ash can modify them for you. Link to pics of my modified - Mr.Stacy 05:06:23 12/10/10 Chart above doesn't seem accurate-Greddy's dont look so good - ZXoltan 09:00:46 12/10/10 Ash did the tests. - Woody75 (Denver) 09:32:33 12/10/10 I agree. Would be nice for someone to reproduce and validate - ZXoltan 09:39:26 12/10/10 You could always just have your ICs flowtested by someone - Ash's Z 10:33:53 12/10/10 Q - BigTDogg (MA) 10:59:09 12/10/10 Why don't you test them all at 200 cfm and 15psi or 20psi - not4resaleZ 13:05:58 12/10/10 The power requirement to move that much air - Jim (Selin Design) 13:35:17 12/10/10 The problem with data logging is you would have to block - not4resaleZ 15:30:05 12/10/10 On a dyno pull you wouldn't have - Jim (Selin Design) 17:14:32 12/10/10 Thermodynamically speaking >>>> - Ash's Z 14:17:14 12/10/10 To put it simply, it's not necessary to do this... - LitlElvis 15:07:16 12/10/10 but your engine will only flow about 200 psf max. (n/m) - not4resaleZ 15:34:26 12/10/10 Re: but your engine will only flow about 200 psf max. - not4resaleZ 15:45:40 12/10/10 That looks to be some rendition of a formula for - LitlElvis 16:00:59 12/10/10 I'm sorry, I mean 200 cfm. This is based on the engine - not4resaleZ 16:07:22 12/10/10 Ok, at 7500RPM and 0psi a 3.0L engine moves ~199CFM - LitlElvis 16:40:28 12/10/10 clarification - aliaZ 17:21:22 12/10/10 I know, I should have used "SCFM" instead of "CFM" - LitlElvis 18:16:07 12/10/10 agreed (n/m) - aliaZ 18:21:08 12/10/10 I would describe it as, when the air filter sees 414 cfm - not4resaleZ 17:26:14 12/10/10 This is a standard formula for pressure drop in a pipe. - not4resaleZ 16:04:19 12/10/10 I like bell intercoolers charts. They test cores using a - not4resaleZ 13:21:15 12/10/10 ...I dont think the Bells have aluminum endtanks like the - ZiNnYc 13:35:42 12/10/10 Greddys only flow a bit more than stock. - The Hawk 12:41:10 12/10/10 This is the opposite of anything I have ever heard. (n/m) - blackomega 13:09:44 12/10/10 2nd- although my info comes primarily from TT.net postings (n/m) - ZXoltan 13:44:34 12/10/10 As discussed above, the chart from Ash - The Hawk 19:07:59 12/10/10 Interesting since in empirial testing i found - ztunerz 20:18:54 12/10/10 Ignore the spelling errors-touchscreen sucks (n/m) - ztunerz 21:05:19 12/10/10 False. (n/m) - Only1Z 14:56:10 12/11/10 500 to 700 (n/m) - Dane (Houston) 00:44:37 12/10/10 how would power from .5 inch larger IC piping compare - Rogy 17:57:44 12/10/10 You haven't been paying attention have you? - CoHPhasor 19:54:56 12/10/10 thk you, I just needed a basis for comparison..words instead - Rogy 22:28:47 12/10/10 Hahah! No worries my friend :-D - CoHPhasor 02:11:10 12/11/10
Post a Followup	You cannot reply to this message because you are not logged in.