Subject	Yea, didn't want to mess up my MS if things dont work out.
Posted by	toykoz32 on December 01, 2010 at 8:43 PM
	This message has been viewed 136 times.
In Reply To	those modded mani's are AMS units right? posted by nissansx on December 01, 2010 at 08:21 PM
Message	If everything goes as plan I will have this done to my MS. Didn't really say anything, he speaks Japanese and I dont. I have some custom pistons from CP, that are Gas ported with a napier piston ring, trying to get these new FM piston rings ( [ http://www.dailytech.com/New+Piston+Ring+Could+Drastically+Improve+Gas+Engine+Efficiency+Longevity/article19406.htm ] ), and upgraded tool steel pins. Cunningham Rods. I have a few options on the cams. Might go with some JWT Solid Cams or a set of custom cams from Escort Racing that a friend has. But I wanna keep my car street-able as possible. Yes these are the Mani's. I spoke with Mike Smith and he might be making some t3 manifolds with waste gate ports on them. I have no will to have these done, but if MS wanted to get one of the sets I have for measurements I would be more than happy to let him do so.
Follow Ups	Texas Mile getting a Little bit Closer !!!! - toykoz32 20:14:25 12/01/10 those modded mani's are AMS units right? - nissansx 20:21:22 12/01/10 Yea, didn't want to mess up my MS if things dont work out. - toykoz32 20:43:17 12/01/10 I wouldn't take the risk of trying a new ring design... - Jim (Selin Design) 22:53:02 12/01/10 I have yet to try to get ahold of Federal Mogul - toykoz32 23:56:13 12/01/10 Who's building the motor? (n/m) - Wright (Ca) 20:23:27 12/01/10 I have yet to decided yet. But . . . - toykoz32 20:52:16 12/01/10 have they done many 1200+ RWHP builds? (n/m) - dpjax 12:00:49 12/02/10 Who? - toykoz32 14:07:40 12/02/10 Why have you removed the inside of the mani from the photo? (n/m) - thumper 20:28:19 12/01/10 Easier for people to see what I am measuring - toykoz32 20:49:28 12/01/10 The rings look awesome, who said diamonds r ONLY a girls BF? - CoHPhasor 21:09:30 12/01/10 Prob. sending them to get extrude honed - toykoz32 21:29:19 12/01/10 Sweet! (n/m) - CoHPhasor 21:32:09 12/01/10 Get it done already, you might be able to keep up then! (n/m) - MafiosoZ 21:20:44 12/01/10 Might? Kind of a understatement :-) 2-3 months. (n/m) - toykoz32 21:30:50 12/01/10 Since I have yet to meet up with you . . The new DD - toykoz32 21:32:55 12/01/10 Ah, yes. It looks good, well see how long you keep that one. (n/m) - MafiosoZ 21:39:53 12/01/10 3076 vs 5858 - toykoz32 23:38:42 12/01/10 Have you fitted them to the car? - sparkie 11:36:48 12/02/10 I had the manifolds machined before i put on the flange - toykoz32 13:33:16 12/02/10 Compressor surge? (n/m) - ZiNnYc 12:44:02 12/02/10 What about it? (n/m) - toykoz32 13:11:08 12/02/10 You dont anticipate that being an issue with these turbos? (n/m) - ZiNnYc 13:41:34 12/02/10 Not from what I have been told . . . Link inside - toykoz32 14:04:58 12/02/10 Still can't wait to see the final result! - ELIM 15:47:39 12/02/10 You guys better. (n/m) - toykoz32 16:10:04 12/02/10 FYI Make sure you register Jan. 15th for the mile, or there - marklar182 16:33:12 12/02/10 Thanks, I think there where some other states - toykoz32 18:11:03 12/02/10 Nice work. So happy to see someone doing somthing different - MikeVar82 18:13:29 12/02/10
Post a Followup	You cannot reply to this message because you are not logged in.