Subject	Fantom is correct. I needed to shave a few pounds and
Posted by	Milo (SATX) on November 16, 2010 at 4:50 PM
	This message has been viewed 183 times.
In Reply To	thats looks like a dzus fastener, and I would assume posted by fantomZ(OH) on November 16, 2010 at 03:08 PM
Message	I ended up breaking the release lever for the fuel door. But remember the quarters are now filled with structure foam, so rather than cutting all that out, this was a simple solution. Eventually we will make the filler into the opposite side of the vehicle where the antenna would normally come out, the goal is to keep the factory location of the fuel tank but step up to a cell later on.
Follow Ups	Been a while. Updated pics of Project LOWFATZ. *PIC HEAVY* - Milo (SATX) 12:20:10 11/16/10 2 questions - KasbeKZ(VA) 12:32:44 11/16/10 I too would like more info on your groove filling technique! (n/m) - Cuis-Z 14:22:17 11/16/10 You want to use something called Duramix. It is like - ChrisZTT(Sacto, CA) 14:38:29 11/16/10 Agree. Duramix is the way you wanna go. I ended up going - Milo (SATX) 16:47:36 11/16/10 yeah that's why i ask. most lower density fillers - KasbeKZ(VA) 17:04:18 11/16/10 been following the thread on 3ZC for quite some time now - zgene4 12:38:15 11/16/10 2nd. Great work! - ConVerTT 12:51:25 11/16/10 Looks good! (n/m) - Dallas DamonZ 12:40:50 11/16/10 Thank you, sir. (n/m) - Milo (SATX) 17:22:36 11/16/10 Great work Milo. (n/m) - Roundabout136 12:43:38 11/16/10 Looking good - RobZ32 12:46:25 11/16/10 Awesome! (n/m) - Evan(CA) 13:10:50 11/16/10 wow! great job. - loco 14:40:40 11/16/10 What's the point of a locking fuel door? Aren't you using a - Dave N 14:53:08 11/16/10 thats looks like a dzus fastener, and I would assume - fantomZ(OH) 15:08:07 11/16/10 Fantom is correct. I needed to shave a few pounds and - Milo (SATX) 16:50:33 11/16/10 Ahh, that makes sense now. Chewing gum and a paper clip - Dave N 18:34:27 11/16/10 Louvers in the hatch? Looking forward to seeing that. (n/m) - chicagozer 10:52:32 11/17/10 question about the cage primer. - fantomZ(OH) 15:15:57 11/16/10 Zinc Chromate Aircraft Grade primer. It's the strongest - Milo (SATX) 16:52:02 11/16/10 This is mainly a street car right? :) (n/m) - jmw23712 15:27:37 11/16/10 I've been following your project on 3ZC...I love it! - TheTwinZ (Peru) 16:00:20 11/16/10 Good job there Miles! Cant wait to see the final product... - rave 16:13:11 11/16/10 Not sure if people are into what I like, so been kind of - Milo (SATX) 16:53:21 11/16/10 After being on here and 3zc for almost a decade you really - Evan(CA) 17:09:42 11/16/10 Good point. I just didn't think people would be into me - Milo (SATX) 17:22:11 11/16/10 I imagine most of the flak you got was about your engine - Evan(CA) 17:35:28 11/16/10 Well. - Milo (SATX) 18:03:45 11/16/10 SBC and be done (n/m) - Adam (NoVA) 09:28:58 11/17/10 Looks like a ton of work - nice. (n/m) - TT XTZ 16:17:34 11/16/10 Cool (n/m) - John (MD) 16:26:57 11/16/10 Heck yeah! (n/m) - John@Z1 16:28:05 11/16/10 Nice! Keep it up. (n/m) - Z_Pilot (GA) 16:33:27 11/16/10 nice! (n/m) - Halo TTZ 18:25:43 11/16/10 Nice car, but it needs a TT engine. Or a VQ35 - BigTDogg (MA) 18:58:17 11/16/10 .... - Halo TTZ 21:12:44 11/16/10 Gutted the hell out of the stock dash. So, it is rather - Milo (SATX) 21:17:53 11/16/10 Nice update. Keep it coming. (n/m) - Boosted1 19:18:05 11/16/10 wow. looking forward to seeing the finished car on a track. (n/m) - Tu 20:34:19 11/16/10 Wow -- now that's a project! - Trailboss 08:02:28 11/17/10 WOW, thats good stuff right there, keep up the hard work! (n/m) - i_drive 09:10:18 11/17/10 when can i drive it - Adam (NoVA) 09:27:22 11/17/10 I'll probably finish the body by January hopefully. - Milo (SATX) 12:46:23 11/17/10 good, i have plenty of time to skinny down for that seat :) (n/m) - Adam (NoVA) 13:30:15 11/17/10
Post a Followup	You cannot reply to this message because you are not logged in.