Subject	I did not know alot of this .Thank you (n/m)
Posted by	xteam300tt on November 05, 2010 at 3:54 PM
	This message has been viewed 428 times.
In Reply To	the problem is shotty workmanship/QC/remanufacturing posted by CoHPhasor on November 05, 2010 at 03:20 PM
Message
Follow Ups	Which injectors have to best success rate , im tired ! - xteam300tt 11:25:36 11/05/10 Sorry, but only you can decide whether changing now is the - kkrofft (OH) 12:12:49 11/05/10 Thanx for your input . (n/m) - xteam300tt 12:24:03 11/05/10 wait, so you read a few posts here about problems with - LJZTT 12:27:10 11/05/10 Almost , i was hoping for a post like yours but was - xteam300tt 13:42:06 11/05/10 meh, dont get suckered into overreacting, while I have - LJZTT 16:03:30 11/05/10 My Nismo 740cc injectors are going on year 5 w/0 problems - Adam (NoVA) 12:43:45 11/05/10 Adam, did you have to - vulcanrush 13:07:47 11/05/10 Not necessary with a '95 efi harness iirc. (n/m) - Wright (Ca) 13:19:33 11/05/10 Correct (n/m) - Bernie (NoVA) 13:20:21 11/05/10 To use a 95 harness what do you do with the cas ? - ztunerz 09:56:15 11/06/10 Yes, as linked to below in an AutoFAQ - BigTDogg (MA) 10:23:52 11/06/10 saw it ty :) (n/m) - ztunerz 10:54:42 11/06/10 The metal spades are not the same so you can't really - Bernie (NoVA) 10:57:51 11/07/10 thank you, Evan - vulcanrush 13:26:59 11/05/10 Bingo (n/m) - BigTDogg (MA) 16:17:27 11/05/10 Okay, but what if you are NOT using a '95 harness? - Gromit 20:17:39 11/05/10 Have Steve do the switched circuit mod. (n/m) - Bernie (NoVA) 23:05:09 11/05/10 Okay, thanks, I will. But I'm surprised... - Gromit 02:01:21 11/06/10 Honestly it's be covered about a 100 times already. - Bernie (NoVA) 09:30:55 11/06/10 Most excellent... - Gromit 03:05:11 11/07/10 I'll be doing the switched circuit mod on your car :) (n/m) - Guapo 23:44:45 11/07/10 Answers: - BigTDogg (MA) 09:06:09 11/06/10 thanks man (n/m) - Gromit 03:06:22 11/07/10 going on 6 years and 55k miles on my 740's/ no problems - aliaZ 16:26:29 11/05/10 we're in a club (n/m) - Adam (NoVA) 16:52:56 11/05/10 I have a new 91 tt auto harness , do i need to do the - xteam300tt 17:25:49 11/05/10 Switched 12V is recommended. the 95's were switched built-in (n/m) - CoHPhasor 17:44:21 11/05/10 Yes. (n/m) - Bernie (NoVA) 23:04:27 11/05/10 Re: Which injectors have to best success rate , im tired ! - MaxxAction 13:58:41 11/05/10 Having a good A/F ratio at the sensor, but a - not4resaleZ 15:37:32 11/05/10 Glad I posted , I needed the schoolin . Thanx (n/m) - xteam300tt 15:59:31 11/05/10 this is an enlightening post, unfortunately I am still - LJZTT 16:06:29 11/05/10 the problem is shotty workmanship/QC/remanufacturing - CoHPhasor 15:20:35 11/05/10 I did not know alot of this .Thank you (n/m) - xteam300tt 15:54:36 11/05/10 So are injectors by nismo and other trusted vendors - xteam300tt 16:07:08 11/05/10 Actually the *only company I know of that - CoHPhasor 17:43:02 11/05/10 I do believe JECS manufactures Nismo injectors. (n/m) - Mr.Stacy 18:13:56 11/05/10 word. JECS is the OEM of factory and NISMO injectors - ali300zx 18:23:44 11/05/10 Thought so, wasn't sure, and didn't want to - CoHPhasor 19:41:25 11/05/10 ahh so glad I have a 96tt engine. dropped in nismo 740's - lakerdude42 15:45:50 11/05/10 Re: Which injectors have to best success rate , im tired ! - SinZT4 16:41:57 11/05/10 From what I've read recently, if you do a straight swap... - Black95 22:59:12 11/06/10 Have you considered JECS? (n/m) - Mr.Stacy 17:57:54 11/05/10 Deatschwerks are usually ok... - flashstar 20:51:19 11/05/10 "Usually ok until they fail"? - Captain Obvious everyone - CoHPhasor 22:24:33 11/05/10
Post a Followup	You cannot reply to this message because you are not logged in.