Subject	Yes ive seen that thread whats your point?, ive seen these
Posted by	Z32TT-R on October 29, 2010 at 12:07 AM
	This message has been viewed 148 times.
In Reply To	Oh, so Im sure youve seen this. posted by ZiNnYc on October 28, 2010 at 08:55 PM
Message	rails in person and installed correctly with no issues, BDE is also an ok setup but seriously their is wood in that kit and too much modification to make fit properly. WF is drop in application besides the minor grinding in some spots, which is way less work then getting BDE on no offense.
Follow Ups	Which parts of the z32 fuel system are not compatible with - FuerGrissa 04:47:40 10/28/10 The 300Degree fuel rails are 100% anodized. (n/m) - ni[X]it 06:22:16 10/28/10 The 300degrees are coated internally as well. - ZiNnYc 06:49:22 10/28/10 My fuel rails are 100% anodized, inside and out. (n/m) - LitlElvis 06:52:25 10/28/10 Is that a recent development? - ZiNnYc 06:54:46 10/28/10 I believe i see my error... - ZiNnYc 07:17:40 10/28/10 All of this E85/alcohol corrosion scare comes from methanol - LitlElvis 08:48:17 10/28/10 Will hard coating prevent meth corrosion? (n/m) - ZiNnYc 09:08:53 10/28/10 Hard anodize will limit methanol corrosion, but eventually - LitlElvis 09:50:48 10/28/10 is this true for lowere concentrations like windhield fluid? - FuerGrissa 10:19:25 10/28/10 I don't know, but my guess is the concentration of methanol - LitlElvis 10:39:51 10/28/10 My washer fluid pump is probably the most corroded part - not4resaleZ 11:52:13 10/28/10 I've seen little evidence of corrosion on bare aluminum - zgene4 12:13:30 10/28/10 the rest of the stock system is fine? (n/m) - FuerGrissa 10:22:05 10/28/10 It has been used without issue. (n/m) - ZiNnYc 11:05:17 10/28/10 Have you seen a Winfactory rail in person? - toykoz32 19:04:47 10/28/10 . - ZiNnYc 20:35:35 10/28/10 So the answer to my question is no. - toykoz32 20:46:08 10/28/10 Oh, so Im sure youve seen this. - ZiNnYc 20:55:11 10/28/10 Yes ive seen that thread whats your point?, ive seen these - Z32TT-R 00:07:33 10/29/10 Wood? It's mechanical grade phenolic resin board... - LitlElvis 11:26:45 10/29/10 Question for you and examples - toykoz32 21:00:49 10/28/10 Do all of those kits use retaining clips and grease - ZiNnYc 21:32:00 10/28/10 I really like the BDE rails, but am suprised how turned off - FuerGrissa 21:50:36 10/28/10 True. It is pretty damn ugly. - ZiNnYc 21:53:19 10/28/10 That person didnt secure the retaining bracket well enough, - Z32TT-R 22:27:22 10/28/10 And how was the problem fixed? - toykoz32 22:45:58 10/28/10 Its pretty damn sexy to me. - toykoz32 22:48:17 10/28/10 I'll look into something different for the mounts. - LitlElvis 11:33:03 10/29/10 Thanks Brett. - ZiNnYc 14:56:48 10/29/10 The injector failing has nothing to do with the rail design - Z32TT-R 22:23:47 10/28/10 Re: The injector failing has nothing to do with the rail design - toykoz32 22:51:06 10/28/10 Woops thought i read somewhere they did, it be nice for - Z32TT-R 00:10:26 10/29/10 Hope everyone used grease or some type of lubricant - toykoz32 22:58:48 10/28/10 Do you have to run cats with E85 for emissions? (n/m) - BigTDogg (MA) 13:42:06 10/28/10
Post a Followup	You cannot reply to this message because you are not logged in.