Subject	I believe i see my error...
Posted by	ZiNnYc on October 28, 2010 at 7:17 AM
	This message has been viewed 183 times.
In Reply To	Is that a recent development? posted by ZiNnYc on October 28, 2010 at 06:54 AM
Message	[ http://www.twinturbo.net/net/viewmsg.aspx?forum=general&msg_id=2299553&forum=general&dtSearch=0 ] Correct me if I'm wrong, but I believe your rails are type 2 anodized, but you say to be safe and make them a type 3 hard coat, which would be a thicker coat and I suppose safer for the corrosive e85? Which would also lend the question, which type of internal anodizing does the 300 degree rail have? src="http://img37.imageshack.us/img37/3649/49186307.jpg">
Follow Ups	Which parts of the z32 fuel system are not compatible with - FuerGrissa 04:47:40 10/28/10 The 300Degree fuel rails are 100% anodized. (n/m) - ni[X]it 06:22:16 10/28/10 The 300degrees are coated internally as well. - ZiNnYc 06:49:22 10/28/10 My fuel rails are 100% anodized, inside and out. (n/m) - LitlElvis 06:52:25 10/28/10 Is that a recent development? - ZiNnYc 06:54:46 10/28/10 I believe i see my error... - ZiNnYc 07:17:40 10/28/10 All of this E85/alcohol corrosion scare comes from methanol - LitlElvis 08:48:17 10/28/10 Will hard coating prevent meth corrosion? (n/m) - ZiNnYc 09:08:53 10/28/10 Hard anodize will limit methanol corrosion, but eventually - LitlElvis 09:50:48 10/28/10 is this true for lowere concentrations like windhield fluid? - FuerGrissa 10:19:25 10/28/10 I don't know, but my guess is the concentration of methanol - LitlElvis 10:39:51 10/28/10 My washer fluid pump is probably the most corroded part - not4resaleZ 11:52:13 10/28/10 I've seen little evidence of corrosion on bare aluminum - zgene4 12:13:30 10/28/10 the rest of the stock system is fine? (n/m) - FuerGrissa 10:22:05 10/28/10 It has been used without issue. (n/m) - ZiNnYc 11:05:17 10/28/10 Have you seen a Winfactory rail in person? - toykoz32 19:04:47 10/28/10 . - ZiNnYc 20:35:35 10/28/10 So the answer to my question is no. - toykoz32 20:46:08 10/28/10 Oh, so Im sure youve seen this. - ZiNnYc 20:55:11 10/28/10 Yes ive seen that thread whats your point?, ive seen these - Z32TT-R 00:07:33 10/29/10 Wood? It's mechanical grade phenolic resin board... - LitlElvis 11:26:45 10/29/10 Question for you and examples - toykoz32 21:00:49 10/28/10 Do all of those kits use retaining clips and grease - ZiNnYc 21:32:00 10/28/10 I really like the BDE rails, but am suprised how turned off - FuerGrissa 21:50:36 10/28/10 True. It is pretty damn ugly. - ZiNnYc 21:53:19 10/28/10 That person didnt secure the retaining bracket well enough, - Z32TT-R 22:27:22 10/28/10 And how was the problem fixed? - toykoz32 22:45:58 10/28/10 Its pretty damn sexy to me. - toykoz32 22:48:17 10/28/10 I'll look into something different for the mounts. - LitlElvis 11:33:03 10/29/10 Thanks Brett. - ZiNnYc 14:56:48 10/29/10 The injector failing has nothing to do with the rail design - Z32TT-R 22:23:47 10/28/10 Re: The injector failing has nothing to do with the rail design - toykoz32 22:51:06 10/28/10 Woops thought i read somewhere they did, it be nice for - Z32TT-R 00:10:26 10/29/10 Hope everyone used grease or some type of lubricant - toykoz32 22:58:48 10/28/10 Do you have to run cats with E85 for emissions? (n/m) - BigTDogg (MA) 13:42:06 10/28/10
Post a Followup	You cannot reply to this message because you are not logged in.