Subject	Yes just dump them in a metal bucket full of PB blaster
Posted by	ZXRider on September 22, 2010 at 2:59 PM
	This message has been viewed 89 times.
In Reply To	Yeah, I managed to get one for $75 shipped. Not too shabby. posted by rojoloco (San Diego) on September 22, 2010 at 04:37 AM
Message	since the only things from the turbo you will be re-using will be the compressor and exhaust housinsg. Use a metal bucket or container since PB blaster might melt/dissolve plastic. There is a small thin O-Ring on the compressor side that you will also need to re-use. I do not think PB blaster will eat through that since I had mine soaked with PB plaster and the O-Ring stayed intact. Buy Zama Posters Here I have nightmares about that happening...I'd be the poor bastard you'd hear about on the news that gets killed by a softball-size chunk while spreading out my body over the hood and screaming "Nooo!" (Having a conversation about hail damage) - BradZ (FL) on March 25, 2005 at 9:56 PM Tell your friend that you could take a dump, light it on fire and that would be hotter shit than his car. Probes suck, that's just all there is to it. - 300ZXpert (someday) on April 04, 2005 at 11:35 PM P.S. You REALLY are on here at ALL hours! And I thought I was bad! :) - zmenon on August 16, 2005 at 3:06 AM LOL...2+2 drivers should grow mullets..."Business in the front...party in the back" ;) - BradZ (FL) on November 29, 2005 at 4:45 PM
Follow Ups	Question regarding CHRA's. - rojoloco (San Diego) 13:29:54 09/21/10 GT28R's are about the same price as sport 500's - ZXoltan 13:41:42 09/21/10 You can change the CHRA's yourself. - MixManMash 13:57:54 09/21/10 Sport 500's will use the same 4-bolt down pipes - Barry(TN) 14:01:38 09/21/10 If you can clock a turbo, you can replace the CHRA. - dogpile 14:26:55 09/21/10 someones selling 530s? Pray tell.. (n/m) - ZiNnYc 15:17:48 09/21/10 Search :-P - MixManMash 15:31:39 09/21/10 Step by step instructions are on Z1's site. - EricTTZ 14:38:51 09/21/10 Sexy Time! - rojoloco (San Diego) 20:13:17 09/21/10 You can do it yourself but certain tools are needed. - ZTicket(Dallas) 17:06:13 09/21/10 According to the write-up... - rojoloco (San Diego) 20:16:15 09/21/10 I just did this and it was a 'snap' - EricTTZ 21:40:58 09/21/10 That's way too expensive - ZXRider 03:23:48 09/22/10 2nd. - Woody75 (Denver) 08:29:27 09/22/10 That's what I meant. Snap ring not slip ring. lol - rojoloco (San Diego) 03:59:51 09/22/10 For $100 EPRacing will coat turbos and during the breakdown - CoHPhasor 02:01:38 09/22/10 I replaced the CHRAs on my turbos - ZXRider 03:26:20 09/22/10 Yeah, other than the plier set, I have all the tools. - rojoloco (San Diego) 04:01:25 09/22/10 PS Did you end up getting your plenum powder coated? - ZXRider 03:28:00 09/22/10 I actually purchased one from another guy. - rojoloco (San Diego) 04:02:16 09/22/10 Figured the money for powder coating could be used - ZXRider 04:07:24 09/22/10 Yeah, I managed to get one for $75 shipped. Not too shabby. - rojoloco (San Diego) 04:37:32 09/22/10 Yes just dump them in a metal bucket full of PB blaster - ZXRider 14:59:52 09/22/10 big 2nd on skipping engine dressup - ali300zx 08:30:16 09/22/10
Post a Followup	You cannot reply to this message because you are not logged in.