Subject	Re: I ran into that problem as well...
Posted by	Marty1Mc on August 26, 2010 at 5:36 PM
	This message has been viewed 43 times.
In Reply To	I ran into that problem as well... posted by Multi_Read (MO) on August 25, 2010 at 08:29 AM
Message	:but I just took a razor blade and cut the rubber boot so it fit snugly around the base of the shifter. It isn't a perfect seal, but its good enough. I don't notice any extra noise or heat in the cabin area. All is well. I did something a little different to solve this. I flipped it boot upside down and used some RTV to seal it to the base. It seals well that way. If I take it off, I'll just clean it up and reseal.
Follow Ups	Z1 short shifter and shifter bracket question. - aquariuscsm 21:34:14 08/24/10 I have one and its great - na300zx (OH) 22:00:56 08/24/10 is this the new style thats bent for LHD cars ? - TTkeeper 23:18:03 08/24/10 It works for either, You just spin it 180* for LH or RHD (n/m) - Spddracer 10:04:56 08/25/10 You can't do that with our shifter or the Cs. - Russell@Z1 13:57:10 08/25/10 If the shift mount is adjustable you can ;) (n/m) - Spddracer 20:20:54 08/25/10 Mine has been on my Z for over 2 years. - Z_Pilot (GA) 22:06:30 08/24/10 If you were to go that route, might consider the shifter - dregos 22:10:21 08/24/10 Z1 shifter is much better than anything on ebay. - Z_Pilot (GA) 22:21:45 08/24/10 Could be and have no experience either way. NP, here. (n/m) - dregos 22:22:37 08/24/10 Btw, I will stick with my SilverTTwins and the SPL bushings. - dregos 22:26:56 08/24/10 Z1 shifter is absolutley nothing like a Mookie or anything - Russell@Z1 23:56:56 08/24/10 "The headache of just not having to assemble it and..... - Multi_Read (MO) 08:32:36 08/25/10 Link just sent to your email. Dre (n/m) - dregos 22:19:09 08/24/10 Thanks everyone! Z1 shifter *ordered* :^) (n/m) - aquariuscsm 22:46:32 08/24/10 Good choice! I enjoy my Z1 shifter. - Multi_Read (MO) 00:41:21 08/25/10 Re: Good choice! I enjoy my Z1 shifter. - Marty1Mc 06:41:43 08/25/10 I ran into that problem as well... - Multi_Read (MO) 08:29:10 08/25/10 Re: I ran into that problem as well... - Marty1Mc 17:36:18 08/26/10 To cure the "boot" problem....... - Spddracer 10:03:42 08/25/10 Looking forward to seeing the final product. (n/m) - Multi_Read (MO) 00:18:33 08/26/10 Also be sure to check all boots and the support brace (n/m) - Cruicad 07:02:50 08/25/10 Nut/bolt/washer. - aquariuscsm 08:29:15 08/25/10 I like mine - lazer(NV) 18:56:12 08/25/10
Post a Followup	You cannot reply to this message because you are not logged in.