Subject	You can't do that with our shifter or the Cs.
Posted by	Russell@Z1 on August 25, 2010 at 1:57 PM
	This message has been viewed 77 times.
In Reply To	It works for either, You just spin it 180* for LH or RHD (n/m) posted by Spddracer on August 25, 2010 at 10:04 AM
Message	The rod is also bent backwards towards the driver. So if you flip the shift rod 180, your hand will hit the console clock area when shifting into 1, 3, or 5. Russell Floyd Z1 Motorsports www.300zx.com 1990+ Nissan Z specialists Used Parts, New parts, Service/Repair and Performance Z1 Motorsports Exclusive Parts Line 2877 Carrollton Villa Rica Hwy Carrollton, Ga 30116 770-838-7777 770-832-9253 (fax)
Follow Ups	Z1 short shifter and shifter bracket question. - aquariuscsm 21:34:14 08/24/10 I have one and its great - na300zx (OH) 22:00:56 08/24/10 is this the new style thats bent for LHD cars ? - TTkeeper 23:18:03 08/24/10 It works for either, You just spin it 180* for LH or RHD (n/m) - Spddracer 10:04:56 08/25/10 You can't do that with our shifter or the Cs. - Russell@Z1 13:57:10 08/25/10 If the shift mount is adjustable you can ;) (n/m) - Spddracer 20:20:54 08/25/10 Mine has been on my Z for over 2 years. - Z_Pilot (GA) 22:06:30 08/24/10 If you were to go that route, might consider the shifter - dregos 22:10:21 08/24/10 Z1 shifter is much better than anything on ebay. - Z_Pilot (GA) 22:21:45 08/24/10 Could be and have no experience either way. NP, here. (n/m) - dregos 22:22:37 08/24/10 Btw, I will stick with my SilverTTwins and the SPL bushings. - dregos 22:26:56 08/24/10 Z1 shifter is absolutley nothing like a Mookie or anything - Russell@Z1 23:56:56 08/24/10 "The headache of just not having to assemble it and..... - Multi_Read (MO) 08:32:36 08/25/10 Link just sent to your email. Dre (n/m) - dregos 22:19:09 08/24/10 Thanks everyone! Z1 shifter *ordered* :^) (n/m) - aquariuscsm 22:46:32 08/24/10 Good choice! I enjoy my Z1 shifter. - Multi_Read (MO) 00:41:21 08/25/10 Re: Good choice! I enjoy my Z1 shifter. - Marty1Mc 06:41:43 08/25/10 I ran into that problem as well... - Multi_Read (MO) 08:29:10 08/25/10 Re: I ran into that problem as well... - Marty1Mc 17:36:18 08/26/10 To cure the "boot" problem....... - Spddracer 10:03:42 08/25/10 Looking forward to seeing the final product. (n/m) - Multi_Read (MO) 00:18:33 08/26/10 Also be sure to check all boots and the support brace (n/m) - Cruicad 07:02:50 08/25/10 Nut/bolt/washer. - aquariuscsm 08:29:15 08/25/10 I like mine - lazer(NV) 18:56:12 08/25/10
Post a Followup	You cannot reply to this message because you are not logged in.