Subject	True but...
Posted by	DVDBURN (MD) on July 29, 2010 at 10:46 AM
	This message has been viewed 163 times.
In Reply To	assuming you are referring to the timing belt idler posted by spyhunterTT(nj) on July 29, 2010 at 05:55 AM
Message	the primary reason is due to stress. It's a common problem whether the tensioner was adjusted incorrectly at a service or whether the stress was caused over time (probably due to poor tensioner function over time). Idler studs break in many makes of cars and cars that have never had any work done. But as you said, incorrect adjustment of the tensioner at service will speed up the problem. I think the space between the (Z) tensioner arm and tensioner body should be somewhere around 4mm but I could be wrong. www.mytwinturbo.com Nissan Data Voice - The first Nissan diagnostic software with a voice! Download my Nissan 300ZX Vin/Model Lookup. Watch an ECZA meet caravan!
Follow Ups	3 blocks from home, idler pulley sheared clean off (n/m) - turboz32 01:44:32 07/29/10 Wow. That's pretty crazy. - pearlwhite94ttz 02:06:11 07/29/10 It's a common problem. - DVDBURN (MD) 02:35:14 07/29/10 Right answer, wrong vendor. Order from Kyle at IPP - pearl5 10:03:34 07/29/10 I think you have BDE and RameyZ mixed up. (n/m) - MixManMash 10:08:55 07/29/10 Yep, thank you for correcting me. (n/m) - pearl5 10:15:20 07/29/10 Re: Wow. That's pretty crazy. - wrxfl 08:13:12 07/29/10 probable cause? - aliaZ 08:34:00 07/29/10 assuming you are referring to the timing belt idler - spyhunterTT(nj) 05:55:28 07/29/10 agreed - aliaZ 07:48:25 07/29/10 RameyZ idler studs adds that extra piece of mind though. (n/m) - ZiNnYc 09:29:12 07/29/10 Awesome! Extra brain mass included w/ the RameyZ studs! FTW! (n/m) - evan_aggie 10:36:58 07/29/10 lol! Nice. - Z_Cherub 10:44:16 07/29/10 agreed (n/m) - aliaZ 12:44:02 07/29/10 Re: RameyZ idler studs adds that extra piece of mind though. - canyoncarver 08:42:51 07/30/10 Theyre chock full of magic (n/m) - ZiNnYc 09:30:02 07/30/10 although there was one idiot who shall remain - spyhunterTT(nj) 06:18:35 07/30/10 Antonio? (n/m) - aliaZ 09:11:41 07/30/10 you guys are ruthless (n/m) - ZiNnYc 09:29:12 07/30/10 True but... - DVDBURN (MD) 10:46:53 07/29/10 oops, forgot... - DVDBURN (MD) 10:50:26 07/29/10 I don't recall the tensioner needing any adjustment - MrPulldown(Tahoe) 12:58:41 07/29/10 oops - aliaZ 13:16:29 07/29/10 I remember now - MrPulldown(Tahoe) 16:09:42 07/29/10 Did you rotate it around like it says in step 47? (n/m) - Broke_as_**** 17:19:17 07/29/10 I have also seen that when putting the upper pulley on - Spddracer 21:29:42 07/29/10
Post a Followup	You cannot reply to this message because you are not logged in.