Subject	he'll be fine for his setup
Posted by	aliaZ on June 25, 2010 at 2:36 PM
	This message has been viewed 71 times.
In Reply To	2nded, but i think this guy will be ok. posted by Antihero on June 25, 2010 at 02:31 PM
Message	he'll max out his injectors before he exceeds the maximum MAF input to the ECU (5.12 volts). Bottom line is if you're flowing enough to exceed 5.12 volts on add, you need a dual pop chip to average the inputs. Yes, you'll lose some resolution, there really isn't any other options that I am aware of on higher power setups, aside from going to MAP
Follow Ups	Dual MAF with S-AFC2 - hunterg 10:29:50 06/25/10 You can.. but it is recommended to use a dual MAF program - KongZTT GT28RS MD 10:33:49 06/25/10 Use the summing function of the S-AFC2 (n/m) - -Grimm- 10:33:53 06/25/10 You can but... - DVDBURN (MD) 11:20:04 06/25/10 Otherwise like he said... - DVDBURN (MD) 13:36:54 06/25/10 Thanks. I am running 555 injectors - hunterg 14:19:50 06/25/10 not good advice. listen to nismo_boost,zgene,& wright (n/m) - Antihero 14:30:00 06/25/10 Re: not good advice. listen to nismo_boost,zgene,& wright - DVDBURN (MD) 15:13:08 06/25/10 If the car comes with an SAFC its actually a decent choice - Antihero 15:24:39 06/25/10 If you were planning future upgrades then yes. - DVDBURN (MD) 15:35:09 06/25/10 didnt catch the stock ecu part. - Antihero 15:25:28 06/25/10 and why would anyone use a dummy maf anymore? - Antihero 14:31:02 06/25/10 Guess what? People do. That's why I was asking, duh! :) (n/m) - DVDBURN (MD) 15:11:07 06/25/10 I ran with a single pop chip for a while - TTFairladyZ 11:21:07 06/25/10 If you use a Twin-POP program with Dual MAF's.... - ZXoltan 12:07:28 06/25/10 Actually it is acceptable to run a dual intake EEPROM when - Wright (Ca) 13:40:08 06/25/10 The answer is NO - nismo_boost31 12:41:08 06/25/10 This makes sense. Thanks for the explanation - hunterg 14:21:23 06/25/10 not necessarily - aliaZ 14:21:58 06/25/10 no need to upgrade, ADD function on the safc - zgene4 13:04:57 06/25/10 Dual MAF sensors and single MAF ECU it is! Thanks all (n/m) - hunterg 14:22:28 06/25/10 eh...depends on how much power you plan on making - aliaZ 14:26:57 06/25/10 2nded, but i think this guy will be ok. - Antihero 14:31:50 06/25/10 he'll be fine for his setup - aliaZ 14:36:55 06/25/10 Exactly! (n/m) - DVDBURN (MD) 15:14:54 06/25/10 BTW. Don't know if this is in the TT.Net archives or not. - DVDBURN (MD) 16:28:50 06/25/10 Is it voltage or amperage doing it? - CoHPhasor 21:27:08 06/26/10 I'm pretty sure the line only takes into account for volts. - DVDBURN (MD) 06:21:08 06/28/10
Post a Followup	You cannot reply to this message because you are not logged in.