Subject	Like I said, You can go over center and cause the pressure
Posted by	Greg D. (Specialty-Z) on May 13, 2010 at 2:47 PM
	This message has been viewed 57 times.
In Reply To	Exedy is wrong also? posted by Spddracer on May 12, 2010 at 11:05 PM
Message	to increase. Flat or barely over center is standard and reasonable. The most that is normally ever done is to go slightly over center and the thinking in this is that if you start over center "slightly" you can break the clutch in and after all the material is flat and broken in your starting at full load. The pressure falls off a cliff if you go very far....
Follow Ups	I love the new SZ High 5 clutch! - Wright (Ca) 14:10:42 05/10/10 I can second the clutch. - HighPsi (NorCal) 14:42:19 05/10/10 yep, pretty happy with mine as well - aliaZ 14:46:00 05/10/10 Nice! (n/m) - TTFairladyZ 14:50:07 05/10/10 Did you make it out to the drag strip yet? (n/m) - Wright (Ca) 14:56:58 05/10/10 Not yet - TTFairladyZ 15:08:45 05/10/10 I think they went a little overboard with cutting in their - Ashman2k2 15:12:46 05/10/10 Stock Flywheel? (n/m) - DarkZide 15:56:12 05/10/10 Yes, I had an rps flywheel in there before but prefer the - Wright (Ca) 16:05:43 05/10/10 Who machined your flywheel? - toykoz32 20:28:27 05/10/10 Triple crown automotive. Without the step the clamping force - Wright (Ca) 22:05:28 05/10/10 Shops get lazy, end users are cheap. - Bernie (NoVA) 00:58:29 05/11/10 The Step "Decreases" Clamp load. - Spddracer 06:35:27 05/11/10 How do you figure? - Ted (92TT) 08:52:04 05/11/10 Wrong - Greg D. (Specialty-Z) 09:57:16 05/11/10 This answer makes sense. (n/m) - Ted (92TT) 11:41:57 05/11/10 lol (n/m) - aliaZ 11:44:58 05/11/10 Ok so with a modified TT PP it does decrease. - Spddracer 20:22:15 05/12/10 Wrong again..... - Greg D. (Specialty-Z) 20:56:54 05/12/10 I think the pictures prove my point. (n/m) - Spddracer 22:00:23 05/12/10 Exedy is wrong also? - Spddracer 23:05:32 05/12/10 Interesting info, thanks. Not what I would have expected. (n/m) - Ted (92TT) 23:28:01 05/12/10 Adding it to my list of counterintuitive clutch facts :-) (n/m) - Ted (92TT) 23:30:20 05/12/10 Like I said, You can go over center and cause the pressure - Greg D. (Specialty-Z) 14:47:12 05/13/10 WTF?? It really has the SZ cut out like that?? Awesome - dogpile 16:25:32 05/10/10 would the cut outs on the disc cause a balance issue? - Firstgearlaunch(Atlanta) 20:45:35 05/10/10 no. the cutouts are 180 from each other (n/m) - aliaZ 23:05:11 05/10/10 I was wondering about the same thing. - SimaYi 23:42:22 05/10/10 np (n/m) - aliaZ 15:26:07 05/11/10 Curious about a couple things that seem counterintuitive... - Ted (92TT) 09:09:39 05/11/10 Info...... - Greg D. (Specialty-Z) 10:18:55 05/11/10 Great job. On my future list. :-) (n/m) - Ted (92TT) 11:44:14 05/11/10
Post a Followup	You cannot reply to this message because you are not logged in.